说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 平面杆机构
1)  planar machinery
平面杆机构
1.
The balance of inertial Force is the problem often occurring in the design of planar machinery.
平面杆机构的设计中 ,惯性力的平衡是经常遇到的问题。
2)  planar linkage
平面连杆机构
1.
Design of slider mechanisms driven by the planar linkage employed in the automatic feed device;
平面连杆机构推动的推板式自动送料装置的设计
2.
Mathematical model for equivalent moment and moment of inertia of a planar linkage;
平面连杆机构等效力矩和转动惯量数学模型
3.
Equivalent moment of inertia for RPR-RRP planar linkage and it s model of neural network;
RPR-RRP平面连杆机构等效转动惯量及其神经网络模型
3)  planar linkage mechanism
平面连杆机构
1.
Computer aided modeling of planar linkage mechanism and development of general analytic software;
平面连杆机构计算机建模与通用分析软件的开发
2.
Kinematic numerical valued inverse solution of planar linkage mechanism based on tree structure
基于树结构的平面连杆机构运动学数值逆解
3.
Based on closed-loop vector equation of planar linkage mechanism,Newton method is introduced this paper for solving position problems of these mechanisms.
从平面连杆机构的闭环矢量方程出发,介绍了求解平面连杆机构位置问题的牛顿迭代法。
4)  Planar six-bar mechanism
平面六杆机构
1.
A new approach of approximate dwell function synthesis for planar six-bar mechanism is presented in the dissertation, which transforms the synthesis of planar six-bar mechanism to the synthesis of two-bar linkage, reduces the variables to four ,by selecting all dimensions of the four-bar mechanism in advance.
本文提出了一种实现平面六杆机构间歇函数综合的简化优化方法,将多维优化转化为四维优化;从工程实际出发,运用连杆机构运动几何学、数学规划和计算机数值计算和图形显示技术等学科的理论成果,对平面六杆机构间歇函数综合进行了深入系统的研究,建立了平面六杆机构间歇函数综合的理论和方法,并给出了相应的算例。
5)  planar four-bar mechanism
平面四连杆机构
1.
Application of VB in the kinematics analysis of planar four-bar mechanism;
VB在平面四连杆机构运动分析中的应用
2.
This paper analyzes all types of planar four-bar mechanisms with sliding pairs and the range of theswing angles or the stroke of the driving and the driven body.
本文对常用的含有移动副的平面四连杆机构进行了类型分析,并分析了主动件和从动件的运动范围。
6)  four-bar linkage
平面四杆机构
1.
Ball’s curve and Burmester’s curve for four-bar linkage;
平面四杆机构的Ball点和Burmester点曲线
2.
Based on the differential geometry, a kinematic geometry model of the planar four-bar linkages is proposed.
对于众多类型的平面四杆机构的运动几何学问题,只需求解最简单的基本机构的位移方程;然后通过角度参量变换模式,便可求得运动几何学参数,为其应用及动态仿真软件的编制提供了理论依据。
补充资料:机械原理:平面连杆机构


由若干个刚性构件通过低副(转动副﹑移动副)联接﹐且各构件上各点的运动平面均相互平行的机构(图1 平面连杆机构示例 )﹐又称平面低副机构。低副具有压强小﹑磨损轻﹑易於加工和几何形状能保证本身封闭等优点﹐故平面连杆机构广泛用於各种机械和仪器中。与高副机构相比﹐它难以準确实现预期运动﹐设计计算复杂。
         平面连杆机构中最常用的是四杆机构﹐它的构件数目最少﹐且能转换运动。多於四杆的平面连杆机构称多杆机构﹐它能实现一些复杂的运动﹐但杆多且稳定性差。
         曲柄存在条件 动力机的驱动轴一般整周转动﹐因此机构中被驱动的主动件应是绕机架作整周转动的曲柄在形成铰链四杆机构的运动链中﹐a﹑b﹑c﹑d既代表各杆长度又是各杆的符号。当满足最短杆和最长杆之和小於或等於其他两杆长度之和时﹐若将最短杆或其邻杆固定其一﹐则另一杆即为曲柄。
         急回係数 在曲柄等速运动﹑从动件变速运动的连杆机构中﹐要求从动件能快速返回﹐以提高效率。即



         
        k 称为急回係数
         压力角 如图2a 铰链四杆机构 中的曲柄摇杆机构﹐若不计运动副的摩擦力和构件的惯性力﹐则曲柄a通过连杆b作用於摇杆c上的力P ﹐与其作用点B 的速度之间的夹角称为摇杆的压力角。压力角越大﹐P 在方向的有效分力就越小﹐传动也越困难﹐压力角的餘角称为传动角。在机构设计时应限制其最大压力角或最小传动角。
         死点 在曲柄摇杆机构中﹐若以摇杆为主动件﹐则当曲柄和连杆处於一直线位置时﹐连杆传给曲柄的力不能產生使曲柄迴转的力矩﹐以致机构不能起动﹐这个位置称为死点。机构在起动时应避开死点位置﹐而在运动过程中则常利用惯性来过渡死点。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条