说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> M/M/1/K排队模型
1)  M/M/1/K queuing system
M/M/1/K排队模型
2)  M/M/1 queuing model
M/M/1排队模型
1.
The M/M/1 queuing model of the elevator service system is presented in this paper.
运用排队论理论建立了电梯服务系统的最少服务一个顾客最多服务r个顾客的成批服务M/M/1排队模型,并给出了r为随机变量时电梯服务系统的一些参数指标。
2.
Considering the characteristics of the AGV convey system, we setup a M/M/1 queuing model and adopt average queue length and remain time as performance indexes, and then estimate whether the results are reasonable according to system demands and the simulation curves of the M/M/1 model.
针对该AGV输送系统的特点,可以建立M/M/1排队模型,并采用平均队长和逗留时间作为性能指标,然后根据系统需求和M/M/1模型的仿真曲线,分析结果的合理性。
3)  M/M/1 queueing model
M/M/1排队模型
1.
Existence and uniqueness of solution for M/M/1 queueing model;
M/M/1排队模型动态解的存在唯一性
4)  queuing model(M/M/1)
排队模型(M/M/1)
5)  M/G/1/K queuing model
M/G/1/K排队模型
1.
The signal transfer function of the generalized state transition diagram can be used to derive a probability distribution of the MAC layer service time and the performance of EDCA from a non-saturated channel to a saturated medium by using presented M/G/1/K queuing model is analyzed.
11e EDCA网络分析模型,该模型引入了空闲状态和不同接入等级的仲裁帧间隔(AIFS)的使用;利用Markov链状态转移图的Z域信号传递函数推导了MAC层平均服务时间的概率分布;结合M/G/1/K排队模型分析了增强分布式信道接入(EDCA)在非饱和和饱和负载下的性能。
2.
11e access mechanism in multi-hop environments and analyzed the MAC layer performance of multi-hop wireless networks,such as MAC layer throughput,the mean packet delay and packet discard probability due to packet collisions,with the impact of hidden nodes by using presented M/G/1/K queuing model.
11e网络模型,结合M/G/1/K排队模型,定量分析在隐藏终端影响下802。
6)  M/G/K model
M/G/K排队模型
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条