说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 行为自动机模型
1)  behavioural automata model
行为自动机模型
1.
The core of the self-healing system is its runtime behavioural automata model which determines the design of the architecture.
自愈系统的核心是其运行时的行为自动机模型,该模型的结构决定了构架的设计。
2)  Dynamic behavior model
动态行为模型
3)  models of unmotivated behavior
无动机行为模式
4)  hybrid automation
自动机模型
5)  behavior model
行为模型
1.
Anomalies detection method of IP forwarding based on behavior model;
基于行为模型的IP Forwarding异常检测方法
2.
The Design and Realization of Perception and Behavior Model in the Virtual Fish System;
虚拟鱼系统中感知和行为模型的设计与实现
6)  behavioral model
行为模型
1.
Intelligent Behavioral Model of Forces Based On Enemy Intention
基于对方意图建模的多Agent智能兵力行为模型
2.
A novel behavioral model using three-layer time-delay feed-forward neural networks(TDFFNN)is adopted to model radio frequency(RF)power amplifiers exhibiting memory nonlinearities.
提出一种三层前馈输入延迟神经网络模型用于建立射频功率放大器有记忆的非线性行为模型。
3.
Technology acceptance model and expectation confirmation theory model are two important behavioral models in the field of information technology adoption, and they respectively explain some influence factors of information system pre-adoption and post-adoption behavior.
技术接受模型和期望证实理论模型是信息技术采纳领域的两个重要行为模型,分别解释了信息系统采纳前和采纳后行为的影响因素。
补充资料:原动机和调速系统数学模型


原动机和调速系统数学模型
mathematical models of prime mover and governor

模型,其动态特性一般只考虑引水管道由于水流惯性引起的水锤效应,即当导水叶开度突然增大时,水压瞬间减小,水轮机瞬时功率不是增大而是减少,反之亦 ┌────┐ │l一{ │ ├────┤ │l+夕1c“│ └────┘ ┌────┐ │「1币 │ ├────┤ │l+,九“│ └────┘ ┌──┐ │LP川│┌─────┐┌─────┬────┐└──┘│ll ││11] │!11,刁 │ └─────┼┴─────┼────┤ │l’Il+,几。│地旦亚01│ └──────┴────┘ ┌─────┐ │ 1一,T’│ │l+0一5sT’│ └─────┘ 图1汽轮机和水轮机数学模型 (a)汽轮机一阶模型.(b)汽轮机二阶模型; (c)汽轮机三阶模型;(d)水轮机动态模型然。这一现象称为水锤现象,或称水击。 当引水管道较短时,一般忽略引水管道的弹性,从而只计及刚性引水管道的水锤效应,即刚性水击。进一步假定水轮机为理想无损,在额定水头、额定转速和额定工况下运行,则尸,和产间的传递函数为 1一sTwl十0 .ssT,(4) 一一Pm一产式中Tw为水流时间常数,即在稳态额定水头条件下,水流经引水管道所需的时间,一般Tw二。.5~45。式(4)是电力系统分析中最常用的水轮机简化模型,见图1(d)。 调速系统傲学模型大型水轮机的调速系统主要有机械调速器和电气液压调速器两类.大型汽轮机的调速系统主要有液压调速器和功预电液调速器两类,后者主要适用于中间再热式汽轮机。电力系统分析中一般采用简化的调速系统数学模型。 水轮机的机械调速器原理如图2(a)。调速器调节过程简述如下:设发电机负荷增加,则水轮机转速下降,侧速部件离心飞摆的A点下移,此时以B点为支点,配压阀2(错油门)活塞下移,压力油进人接力器3(油动机)的活塞一侧,从而活塞移动,加大导水叶开度,使水轮机出力提高,和外界负荷平衡,转速回升,在颇率调节中称此过程为一次调频。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条