说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 约束点
1)  constrained point
约束点
1.
In this paper, serial algorithms associated with editing Delaunay Triangulation oriented huge terrain are presented which based on the spatial index of quad tree, including the algorithm of adding constrained point, the algorithm of adding constrained line and the algorithm of fast searching the group of common vertex triangulation.
本文在基于四叉树分块构建Delaunay三角网的基础上,设计与实现了面向大地形编辑的以四叉树为空间索引的三角网交互实时编辑系列算法,其中包括约束点的加入、约束线的加入以及共点三角形的快速查找算法。
2.
The constrained texture mapping algorithm is an approach of texture mapping,and it can maintain the alignment of the corresponding features in the texture mapping process by the predefined constrained points.
本方法首先通过手工交互在模型和纹理上添加约束点,用来标记模型以及纹理上对应的特征位置;在网格模型上添加约束点的同时,采用逐点插入法将约束点插入到网格模型中,并使用局部优化法对网格进行优化,保证新产生的网格为Delaunay三角网格;然后,对纹理进行Delaunay三角划分,根据纹理上约束点的拓扑连接关系,对模型采用逼近的最短路径进行三角剖分;接着对分割后的网格以及纹理采用径向基函数实现纹理映射;最后根据网格点所处的位置和属性,采取相应的方法进行优化。
2)  constraint points
约束点
1.
Then,a new method to compress the non-topology polygon data based on constraint points is put forward.
分析了常规压缩算法(如Douglas-Peucker算法)压缩无拓扑多边形数据会产生公共边界不一致现象,认为出现此现象的原因是多边形公共边界的压缩起始点选择不一致,进而提出了一种新的基于约束点的无拓扑多边形数据压缩算法。
3)  pole constraint
极点约束
1.
Research on ship ant rolling control with robust pole constraint;
鲁棒极点约束的船舶减摇控制研究
2.
Firstly,based on the T-S fuzzy model of ASV re-entry attitude dynamic system,considering external disturbance and system uncertainties,the stabilization problem of angular rates and attitude angles is studied,then combining with pole constraints,an existence condition for H_∞fuzzy guaranteed cost control law with pole constraints is derived.
首先基于ASV再入姿态动态系统的T-S模糊模型,考虑外界干扰和系统的不确定性,考察了姿态角速率和姿态角的镇定问题,然后结合极点约束,导出了具有极点约束的H_∞模糊保性能控制律存在的条件。
3.
The uncertain attitude dynamic system descriptor during ASV’s (aerospace vehicle’s) re-entry phase based on T-S fuzzy model with parameter perturbation is considered firstly, then, the stabilization problems of attitude angles and angular velocity errors are researched, and combined with disk pole constraints, a condition for the existence of fuzzy guaranteed c.
研究了空天飞行器(ASV)再入姿态的具有闭环极点约束的模糊保性能控制律的设计问题。
4)  joint constraint
节点约束
1.
Influence of glass and joint constraint on loading capacity of monolayer cable net for point supported glass buildings;
玻璃及节点约束对单层索网承载性能的影响
5)  corner constraint
角点约束
1.
In the whole matching process,the corner constraint and the edge constraint were proposed to guarantee the matching speed.
在匹配过程中,为了保证其快速性引入了两种新约束:角点约束与边缘约束。
6)  MPC
多点约束
1.
"PATRAN" is used to create a canopy FEM for an aircraft using MPC to simulate the flexible attachment between plexiglass and frame.
采用PATRAN建立了某型飞机座舱盖有限元模型,用多点约束模拟玻璃边缘与骨架及弧框之间的软连接。
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条