说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 绕回检测
1)  turn-round detecting
绕回检测
1.
The method of the fault diagnostic for sensors in measurement and control system is given,including Kalman filter and WSSR,and using turn-round detecting technology to detect the faul of the channels.
给出用于测控系统的故障诊断的方法,其中包括用卡尔曼滤波和残差加权平方和方法诊断测控系统中传感器的软/硬故障,用绕回检测技术检测测控系统中的量测通道的故障。
2)  cut-through test method
回绕测试法
3)  checking spring range
回弹检测
1.
So that when conducting the blasting excavation,the measures of controlling vibration velocity,monitoring vibration extent,checking spring range,sound wave inspection and so on were .
爆破开挖采用振速控制、振动监测、回弹检测和声波检测等先进技术,使拉西瓦水电站坝肩和基础开挖达到国内一流水平,堪称“精品工程”。
4)  Echo detecting
回波检测
5)  detection circuit
检测回路
1.
Detection circuit s principle of DC sensor based on self-balance of magnetic potential and feedback compensation is discussed.
论述了磁势自平衡回馈补偿式直流传感器检测回路的工作原理,利用一对检测铁芯和线圈对一次被测电流和二次平衡电流磁势之差进行检测。
6)  data logging
巡回检测
补充资料:厂房构件回弹检测


厂房构件回弹检测
rebound testing of component part of industrial building

ehangfang goulian huitan lianee厂房构件回弹检测(rebound testing of eom-ponent part of industrial buileding)利用回弹仪检侧厂房混凝土构件表面硬度,并以此推算混凝土强度的非破损性厂房安全检查方法。 回弹仪是采用一弹簧驱动的重锤,通过弹击杆弹击混凝土表面,再测出重锤反弹距离,以回弹值N(反弹距离与弹簧初始长度之比)作为与混凝土强度相关的指标推算出混凝土的强度。回弹仪按冲击动能的大小分为重型、中型、轻型三种。目前中国应用最广泛的是中型回弹仪。 通过大量试验,建立了回弹强度瓦1与平均回弹值万的回归方程式 R。=0 .025可一’“‘08 x 10一。。358乙式中万为混凝土平均碳化深度。 该回归方程的相对误差为士17.0写,相对标准差为18.0%。当L二O时,相关系数为0.87。 为了获取R。值,在被测构件表面取一15cm又15cm的测区,用回弹仪在相对的两侧面上分别均匀弹击8个测点,测出回弹值,去掉3个最大值和3个最小值,取剩余的10个测点的平均值,即为该测区的回弹值而,查R。一而曲线,得到该测区的回弹强度值Rn。为了评定单个构件或同批构件的混凝土强度,必须有足够数量的测区,求出各测区的回弹强度的平均值瓦与标准差Sn,再用概率法评定构件的混凝土强度R。其计算公式为 R~R。一asn式中a值视结构的重要性按下表选择。 “的取值范围带呀牛
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条