1) wet-winding craft
湿法缠绕工艺
1.
This paper attempts to take advance of wet-winding craft which is solidified in infrared way and make epoxy-polyester-fiber layer-pressing glass pipe and solve above-mentioned questions through polyester-fiber′s anticorrosive character to achieve little partial discharge and leak electricity and raise insulating grade.
本课题正是为了解决这个问题 ,拟利用湿法缠绕工艺在远红外光下固化成型技术 ,制造出环氧涤纶层压玻璃布管 ,利用涤纶良好的耐腐蚀特性来达到防腐的目的 ,从而减少局部放电和泄漏电流 ,提高绝缘强度。
2) Wet filament winding
湿法缠绕
1.
The epoxy resin formula suitable for pressure vessel for water treatment with wet filament winding is designed.
设计了一种适合水处理容器湿法缠绕使用的环氧树脂体系 ,该体系在室温有较长的凝胶期 ,粘度低 ,可在室温下凝胶、固化 ,在 80℃固化良好。
2.
A series of epoxy resins were designed for carbon fiber wet filament winding.
设计了一系列针对碳纤维湿法缠绕的环氧树脂基体,测试了树脂浇注体及其复合材料的力学性能和热机械性能,研究了树脂基体对碳纤维复合材料界面性能的影响。
3) wet-winding
湿法缠绕
1.
A novel epoxy resin suitable for filament wet-winding of pressure vessel for reverse osmosis was developed and used in a composite based on a middle-temperature curing agent and a highly effective reactive toughener.
使用一种新型中温固化剂和高效活性增韧剂,制备了一种适合膜壳湿法缠绕用的中温固化环氧树脂。
2.
In order to replace the stainless steel with epoxy composites in the inner high pressure vessels for reverse osmosis which is used to produce highly purified water, a toughened epoxy resins matrix, which is suitable for the wet-winding of glass fiber composite, was studied.
工业上广泛使用反渗透膜仓制备高纯水,为了用玻璃钢替代不锈钢,研究了一种适合湿法缠绕的反渗透膜仓用韧性环氧基体。
4) wet winding
湿法缠绕
1.
Research on epoxy resin matrix/carbon fiber composite by wet winding;
碳纤维湿法缠绕用环氧树脂基体研究
2.
Study on resin matrix of T800 carbon fiber composites for wet winding;
湿法缠绕用T800碳纤维复合材料基体研究
6) wet winding technology
湿法缠绕成型
1.
In this paper the reinforced materials used in wet winding technology are briefly introduced and study progress in the wet winding technology and suitable resin matrix are also reviewed.
相对于干法缠绕成型而言 ,湿法缠绕成型可有效降低复合材料的制造成本。
补充资料：湿碰湿工艺
分子式：
CAS号：
性质：喷涂的第一道漆膜还没有实干时接着就喷涂第二道，这种喷涂工艺叫做“湿碰湿”。是一种节约能源、减少工序的方法，但并不适用于所有的涂料。有的涂料会流坠、起皱纹，影响漆膜干燥。适于湿碰湿的漆种有氨基漆、过氯乙烯和聚氨酯漆、环氧基漆。
CAS号：
性质：喷涂的第一道漆膜还没有实干时接着就喷涂第二道，这种喷涂工艺叫做“湿碰湿”。是一种节约能源、减少工序的方法，但并不适用于所有的涂料。有的涂料会流坠、起皱纹，影响漆膜干燥。适于湿碰湿的漆种有氨基漆、过氯乙烯和聚氨酯漆、环氧基漆。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条