1) optical isolate
光隔离
1.
Using this common opt-coupler, a linear and optical isolated voltage transmitter with temperature compensation was designed.
使用这种常见的光电耦合器件,设计完成了一种具有温度补偿功能的线性光隔离电压变送器。
2) optical isolator
光隔离器
1.
Suppression of SBS in fiber hydrophone by optical isolators based on Michelson fiber interferometer;
光隔离器法抑制Michelson干涉型光纤水听器中的SBS
2.
Study on structure of optical isolators;
光隔离器的结构类型研究
3.
Study on Polarization-independent Optical Isolator and Its Arrayed Construction;
偏振无关型光隔离器及其阵列的研究
3) light coupling isolation
光耦隔离
1.
Real-time sampling of single battery voltage during charging or discharging is implemented based on AT89S52 control core,AD629 protective circuit,and linear light coupling isolation of disturbing signal.
本文以AT89S52为控制核心,以AD629为保护电路芯片,通过线性光耦隔离干扰信号,实现了充放电过程中单体电池电压的实时采集。
4) photoelectricity isolation
光电隔离
1.
Using the method which the photoelectricity isolation and the transformer isolates to solve has gathered the question which the electric circuit and th.
用一种以单片机技术为核心,利用V/F转换的方法对单体蓄电池电压进行实时监测,采用光电隔离与变压器隔离的方法解决采集电路和单片机处理电路电气隔离的问题。
5) isolator
['aisəleitə]
光隔离器
1.
Study of polarized beam splitting in walk-off mode polarization-independent isolators;
Walk-off型偏振无关光隔离器中偏振光分束研究
2.
This paper introduces a new kind of polarization independent isolator,presents the design of the walk off mode one stage polarization independent isolators.
介绍了新型的偏振无关光隔离器 ,给出了 walk- off型单级偏振无关光隔离器的设计及原理分析 ,并对其性能进行了测试。
3.
The radical principle of a POlarization- independent optical isolator using YVO4 wedge is presented in this paper.
介绍了用钒酸钇晶体的与偏振无关的Ｗｅｄｇｅ型光隔离器的基本原理，用琼斯矢量法得到了插入损耗和隔离度的数学表达式，并介绍了隔离器的结构设计。
6) optical isolation
光电隔离
1.
The design of intelligent conversion with optical isolation based on communication between LabVIEW and PLC is discussed.
详细介绍了基于LabVIEW与PLC之间通信的带有光电隔离的智能转换器的设计;阐述了从PLC接口上高效率的产生电路所需的电源;给出了实现RS-232接口和RS-485接口的智能转换的硬件电路,采用双光隔提高数据传输速率。
2.
The article introduces an ISA RS232-RS422/RS485converters card with optical isolation.
本文针对ISA总线标准,设计了一种带光电隔离的RS232转换卡,它既能实现RS232至RS485的转换,又能实现RS232至RS422的转换,较好地实现了工业控制现场远程数据传输功能。
3.
The digital image signal is converted from RS-422A to standard TTL signal by using level conversion and optical isolation and then stored in the static RAM by FPGA.
在硬件方面,通过电平转换和光电隔离将RS-422A差分电平的数字图像信号转换为标准TTL信号,经过FPGA自动存储在静态RAM中,接收完毕后由DSP将存储的图像数据经过VXI接口传至上位机。
补充资料：表光合强度(见光合强度)
表光合强度(见光合强度)
forecast of sowing or transplanting time
b iaoguanghe qiangdu表光合强度见光合强度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条