1) starting-braking process
起制动过程
2) starting process
起动过程
1.
Investigation on the starting process of the direct impulse combustion wind tunnel
直连式脉冲燃烧风洞起动过程研究
2.
The result showed that the conveyor has big design parameter,appropriate starting velocity,little dynamic belt tension change and steady starting process.
通过对大倾角上运带式输送机的起动过程进行分析建模,给出了其边界条件和求解方法。
3.
During the research of 11kW rare earth permanent magnet brushless DC motor starting process,the control strategy by slope voltage was used to reduce the higher current.
在对11 kW稀土永磁无刷直流电动机起动过程研究中,针对起动电流过大,采用斜坡电压的方法进行控制。
3) start-up process
起动过程
1.
Investigation on start-up process of expander cycle liquid propellant rocket engine;
膨胀循环发动机起动过程研究
2.
Utilization of the by-pass system in start-up process of turbo-generator set has been described in detail,including the control of magnitude in practical opening degree for the by-pass valve,and its right opening time.
详细描述了在汽轮发电机组起动过程旁路系统的运用,包括旁路阀实际开度的大小及其开启时机的控制。
3.
According to the characteristics of fanjet on tactical missile,the total start-up process of fanjet is described,and related concepts are introduced.
针对用于战术导弹上的涡扇发动机的自身特点,阐述了其整个起动过程,介绍了与之相关的概念。
4) startup process
起动过程
1.
Research of damage-mitigating control for startup process of liquid-propellant rocket engines;
液体火箭发动机起动过程减损控制研究
2.
The results indicate the helium gas turbine may work in the high efficient domain during the startup process and not be choked.
建立了氦气轮机的集总参数数学模型,在Matlab/Simulink下开发了仿真模型,针对起动过程,按照设计要求的条件,进行了起动过程的动态仿真。
5) starting procedure
起动过程
1.
At the same time,by using this simulation model,the analysis of the starting procedure of induction motor is presented to demonstrate its correctness and a series of merits such as shutcut,agility,convenience,intuitionisticness and so on.
本文从异步电动机α ,β ,0坐标系统的数学模型出发 ,利用Matlab语言的Simulink功能给出了异步电动机的一个通用而简单的动态仿真模型 ,并把该模型应用于异步电动机的起动过程分析研究中 ,通过实例验证了模型的正确性 ,并证明了该模型具有快捷、灵活、方便、直观等一系列优点 。
2.
The induction motor starting procedure in various conditions can conveniently be analyzed by using imteractive design program.
从感应电机的数学模型出发 ,推导出感应电机的状态方程式 ,利用MATLAB语言的强大计算能力和灵活图形处理能力 (包括用户界面设计 ) ,直接方便地得到感应电机起动时的各种性能参数的曲线 ,通过交互式设计途径 ,可以方便地对在各种条件下起动的感应电机起动过程进行分析。
6) start process
起动过程
1.
By using TDZBS3500-12 type synchronous motor s parameters, the start process is validated and the emulation result testifies its validity.
利用TDZBS3500-12型同步电机参数[1],对其起动过程和运行特性进行验证,仿真结果证明了模型建立的正确性。
2.
The hardware and software are introduced,and the start process is analyzed .
介绍了一种无位置传感器无刷直流电机控制系统的硬件结构和控制软件 ,并对电机的起动过程进行了分析。
补充资料：制动器制动力分配系数
两轴汽车的前、后制动器制动力的比值一般为固定的常数。通常用前制动器制动力对汽车总制动器制动力之比来表明分配比例，即制动器制动力分配系数。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条