1) mutual inductance sensor
互感式传感器
1.
, Nanchang 330029, China) Abstrct: In this paper, the basic principle of mutual inductance sensor applied to the position measuring has been introduced.
介绍了互感式传感器在位移测量中的基本原理。
2) mutual inductance transducer
互感传感器
3) mutual-inductance transducer
互感<应>传感器
4) variometer of mutual inductance
互感式变感器
5) inductive sensor
电感式传感器
1.
Based on long stator slotted effect of linear synchronous motor in high-speed maglev train,the principle of slot detection,hardware structure of the phase detector and signals subdivision with DSP were presented,the scheme of phase detection was proposed,and a new phase detector was developed based on inductive sensors and Digital Signal Processor(DSP).
为了实现高速磁浮列车用直线同步电机相位的精确检测,提出了基于定子齿槽效应的相位检测方案,并采用电感式传感器和数字信号处理器,设计了相位检测器。
2.
A new method is forwarded to detect the rotor position for linear synchronous motor in high speed maglev train based on inductive sensor and DSP.
针对高速磁浮列车用长定子直线同步电机的特点,提出了一种基于电感式传感器和DSP的电机动子位置检测新方法。
3.
Inductive sensors are widely used in engineering due to their simple structures, high output capacities, good linearity, good disturbance resistance, good stability and low prices.
电感式传感器具有结构简单可靠、输出功率大、线性好、抗干扰和稳定性好、价格低廉等特点,在工程中获得了广泛的应用。
6) inductance sensor
电感式传感器
1.
An inductance sensors signal processing module;
一种电感式传感器信号处理模块
2.
It researchs the measurement of rev in the grinding wheel dynamic balance test,introduces the basal principle and structure of a kind of new inductance sensor.
介绍一种新型的电感式传感器的基本原理及结构、相关DSP数字信号处理系统,并对测速精度进行了理论分析,得出了其性能参数。
3.
With this method,the principles,hardware structure and signal processing of an experimental system based on inductance sensor and FPGA are elucidated.
阐述了基于电感式传感器和现场可编程门阵列(FPGA)信号处理的悬浮间隙测量系统的硬件结构、工作原理及其信号处理方法。
补充资料：变压器式传感器
利用变压器作用原理把被测位移转换为初、次级线圈互感变化的变磁阻式传感器。它由两个或多个带铁心的线圈构成，初、次级线圈间的互感能随衔铁或两个线圈间的相对移动而改变。当用适当频率的电压激励初级线圈时,次级线圈的输出电压将随互感的改变而变化,从而将被测位移转换为电压输出。这种传感器在使用中常采取两个同名端串接的次级绕组线圈，以差动方式输出，所以又称为差动变压器式传感器。变压器式传感器的特点与电感式传感器相同，有时亦称电感式传感器。但变压器式传感器在设计上具有更大的灵活性，应用更为广泛。旋转变压器、感应同步器、自整角机都属于变压器式传感器。变压器式传感器主要用于测量位移和能转换成位移量的力、张力、压力、压差、加速度、应变、流量、厚度、比重、转矩等参量。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条