1) point cathode
点阴极
1.
In this paper,effects of point cathode anodic bonding are theoretically investigated by using electrical circuit analog.
为此 ,本文用等效电路的方法研究了点阴极情况下的电场辅助阳极连接效应 ,计算了连接电流、连接孕育期和紧密接触面积。
2) cathode spots
阴极斑点
1.
Advances in vacuum arc cathode spots
真空电弧阴极斑点的研究进展
2.
By using a Scanning Electron Microscope (SEM), the tracks of cathode spots on the surface of nanocrystalline Cu cathode produced after the first discharge with peak current of 10 A was investigated.
采用扫描电子显微镜(SEM)观察了纳米Cu阴极在峰值电流为10A的小击穿电流下首击穿后的阴极表面烧蚀形貌,发现纳米Cu的阴极斑点从产生到熄灭期间的运动(即短程运动)并不是随机的,而是有一定取向的;进一步通过和常规Cu首击穿烧蚀形貌对比,分析了产生有向运动的原因。
3.
The tracks of cathode spots produced after the first discharge on the surfaces of nanostructured and conventional W-Cu cathodes were investigated using a scanning electron microscope (SEM), and the influence of microstructure of composites on the morphology and movement of cathode spots was studied.
采用扫描电子显微镜观察了W-Cu复合电弧阴极材料首击穿后的表面形貌,研究了复合阴极材料微观结构对阴极烧蚀形貌和阴极斑点运动的影响。
3) cathode spot
阴极斑点
1.
The traces of cathode spots on the surface of coarse-crystalline and nano-crystalline CuCr25 alloys have been observed using a scanning electron microscope (SEM).
采用扫描电镜对纳米晶和粗晶CuCr25合金阴极斑点蚀坑形貌进行观察。
2.
The tracks of cathode spots produced after on the surfaces of cathode activated with different size ThO2 were investigated using a scanning electron microscopy.
用扫描电镜对具有不同大小ThO2粒子的阴极材料击穿后表面上阴极斑点的形貌进行了观察。
3.
The discrimination between CuCr25 and CuCr50 alloys for the cathode spot craters with peak currents of 10 A and 80 A has been studied in this paper.
研究了在峰值电流分别为10A和80A的小击穿电流下,CuCr25与CuCr50合金阴极斑点蚀坑形貌的差异。
4) cathode hot
阴极热点
5) cathode spot
阴极炽点
6) cathode spot
阴极辉点
补充资料：闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
（一）加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度（mm） | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
（二）结构性能 | |||||||
1、离合器、制动器接通率，当滑块行程次数≤16次/分时为70%，≤25次/分时为60%，≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
（三）噪声dB（A） | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | ＞88 | |||
2、公称力＞400kN | ≤87 | ≤88 | ≤90 | ＞90 | |||
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条