说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 一致有界模
1)  module of uniformly bounded
一致有界模
1.
It is proved that every indecomposable module over super-Virasoro algebras is one of the following modules: i) the module of uniformly bounded; ii) the module of category Θ; iii)the module of category Θ-; iv) the module with V(0) as its top composition factor.
证明了Virasoro超代数的不可分解模一定是下述模之一i)一致有界模;ii)范畴Θ的模;iii)范畴Θ~-的模;iv)具有平凡模V(0)作为其复合因子的一类模。
2)  uniformly bounded norm
模一致有界
1.
A property of sequence of functions with uniformly bounded norm in C~n;
C~n中模一致有界函数列的一个性质
3)  uniform boundedness
一致有界
1.
By means of Galerkin approximation, uniform boundedness and dissipa tiveness of delay reaction-diffusion equations are studied.
使用Galerkin逼近的办法,探讨时滞反应扩散方程解的一致有界性和耗散性。
2.
The authors investigate global properties and uniform boundedness of impulsive differential equations with variable times using comparison principle.
运用比较原理研究了具有可变脉冲时刻的脉冲微分方程解的整体性质,给出了解一致有界的充分条件。
3.
By using Liapunov functional equation and Razumikhin skill,the uniform boundedness and uniformly final boundedness of Volterra calculous equation s solution were studied and their sufficient conditions were given as well.
利用Liapunov泛函方程和Razumikhin技巧,研究Volterra积分微分方程解的一致有界性与一致最终有界性。
4)  uniform boundness
一致有界
1.
Under appropriate conditions, using some prior estimate s techniques of Holder inequality, comparison principle of ODE, Gagliard-Nirenberg , Poincare inequality, Gronwall inequality and imbedding theorem, we obtain the global existence and uniform boundness of solutions.
本文利用抛物型方程解的先验估计方法给出了一类强耦合系统解的整体存在性及一致有界性。
2.
Under the appropriate conditions,using some prior estimate s techniques of Hlder inequality,comparison principle of ODE,Gagliard-Nirenberg,Poincaré inequality,Gronwall inequality and imbedding Theorem,we obtain the global existence and uniform boundness of solutions.
考虑一个耦合抛物系统的初边值问题,通过利用H lder不等式,常微分方程的比较原理,Nirenberg-Gagliard不等式以及嵌入定理等先验估计的技巧给出了这类系统解的整体存在性及一致有界性。
3.
A uniform boundness theorem for the convergent and uniform (R) integrable sequence of function is given.
给出了收敛的一致(R)可积函数列的一致有界性定理,并指出一致有界是收敛的(R)可积函数列一致(R)可积的必要条件,但不是充分条件。
5)  uniformly bounded
一致有界
1.
Using multiple Lyapunov functions,a sufficient condition is derived to ensure that the switched nonlinear systems are uniformly bounded and uniformly ultimate bounded.
基于李雅普诺夫函数方法,给出了无激励非线性切换系统一致有界和一致最终有界的充分条件。
2.
Let (f n) ∞ n=1 be a sequence of function on the bounded closed interval ,We proved that the conclusion of Arzela s Theorem is also true if (f n) ∞ n=1 is weakly uniformly bounded and not uniformly bounded on .
证明了在Arzela定理中 ,将函数列 (fn) ∞n =1在一闭的有界区间 [a ,b]上一致有界减弱为“弱一致有界”时 ,定理的结论仍成
3.
We establish the week laws and strong laws of large numbers by using the uniformly bounded conditions.
利用一致有界条件,建立了弱大数定律和强大数定律。
6)  Uniform bounded
一致有界
1.
We set up week laws of large numbers by using the uniform bounded condition.
利用一致有界条件,建立弱大数定律,改进了目前的某些结果,并找到弱大数定律与强大数定律的内在差别。
2.
A criteria of the uniform boundedness and uniform ultimate boundedness and global asymptotic stability of solution is obtained by applying Lyapunov functional method and matrix analysis technique.
利用Lyapunov泛函方法和矩阵分析技巧,得到了系统的解是一致有界和一致最终有界及全局渐近稳定性的判别准则。
补充资料:凹模、凸凹模工作型面加工工艺过程
1)备料。 n
    2)锻造。锻成长方形的坯料(每件留长工艺夹头)。 n
    3)热处理。退火。   n
    4)铣(刨)削。铣(刨)削六面成长方形模块。 n
    5)磨削。磨削上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度。 n
    6)钳工加工。用平板和划线盘按图划线,并打样冲眼;用钻头钻螺纹底孔;用圆柱销孔的预孔;用钻头钻挡料销让位孔;用钻头在中心处钻穿丝孔等;正、反面孔口倒角;凸凹模用钻头孔扩,保证刃口高度;攻螺纹;铰孔。n
  7)铣削。平口钳装夹工件;用的立铣刀铣削型孔至尺寸,保证深度。 n
   8)热处理。凹模工件淬硬至HRC60~64,凸凹模工件淬硬至HRC58~62。 n
   9)平磨。磨上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度至图要求;退磁。 n
   10)线切割。按图编制线切割程序,切割模型孔成形,留单面研磨余量0.005 mm。 n
   11)钳工加工。研光线切割面: n
   12)检验。 n复合冲裁模的装配应选择凸凹模作为装配基准件,先装下模部分,后装上模部分
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条