说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 三因素模型
1)  three-factor model
三因素模型
1.
Empirical Evidence for Fama-French Three-Factor Model in Domestic Securities Market;
Fama-French三因素模型在国内证券市场的实证研究
2.
On the basis of newest 96 month stock data from 01/ 1996 to 12/2003,the three-factor model was researched and tested.
采用深市的股票数据(1996—01~2003—12)对Fam a等的三因素模型在我国证券市场上进行了检验。
3.
Using the three-factor model, this paper studies the long term performance of 71 new shares listed in SSE in 1996 and draws the conclusion that the long-run underperformance of IPOs exists in Chinese security market, whose degree has decreased slowly over time.
本文利用Fama-French三因素模型对1996年在上交所上市的71只新股的长期表现进行了研究,认为我国存在长期弱势现象,但弱势程度在逐渐减弱。
2)  FF three-factor model
FF三因素模型
1.
According to the method of FF three-factor model,BM ratio was replaced into the beta value to construct a new three-factor model,in which the market excess return,size and beta were included.
以收益率与系统流动性因子的β值作为系统流动性风险的代理变量,按照FF三因素模型的方法,将账面市值比替换成β值,构建新的包含市场超额收益、公司规模和β值的三因素模型,研究系统流动性风险与我国股市超额收益的关系。
3)  Fama-French three-factor model
Fama-French三因素模型
4)  three-factor affine model
三因素仿射模型
5)  Three-factor Pricing Model
三因素定价模型
6)  three factor optimization model
三因素优化模型
1.
Using portfolio profits maximum of bank\'s assets as objective function,positive yield skenewss as constraint to reduce the portfolio yield probability of smaller than its mean,value at risk as constraint of assets\' risk,the three factor optimization model of mean-deviation-skewness on loans portfolio is set up.
以银行各项资产组合收益率最大化为目标函数,以收益率偏度大于零控制银行重大损失发生的概率,以组合风险价值VaR风险限额为约束条件控制资产组合风险的大小,建立了贷款组合的"均值-方差-偏度"三因素优化模型。
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条