说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 霍尔开关传感器
1)  Honeywell switch sensor
霍尔开关传感器
2)  Hall switch sensor
开关型霍尔传感器
1.
Principle and engineering realization of Hall switch sensor;
开关型霍尔传感器的原理与工程实现
3)  Hall sensor
霍尔传感器
1.
Application of the Hall sensor in the rotating speed of locomotive;
霍尔传感器在机车测速中的应用研究
2.
High accuracy magnetic field measurement methods based on Hall sensor;
基于霍尔传感器的高准确度磁场测量方法
3.
Hall sensor test system based on single chip microcontroller;
基于单片机的霍尔传感器测试系统
4)  Hall transducer
霍尔传感器
1.
Improving the precision of Hall transducer;
提高霍尔传感器精确度的研究
2.
The principle of monitoring steel-cord conveyor belt joint breaking by Hall transducer and the mathematics model of measuring the belt joint elongation is discussed.
论述了用霍尔传感器通过测量接头拉伸量来进行钢绳芯输送带接头损伤和断裂状况监测的原理以及用于测量诊断的数学模型,并研制成功包括霍尔传感器与变送器、以及Z-80上开发的故障诊断软件在内的一套监测系统,该系统可用于皮带损坏、断裂信号的拾取、贮存、处理、诊断和预报等。
3.
A kind of magnetic sensor array based on UGN3503U linear Hall transducer was presented.
叙述了一种基于UGN3503U线性霍尔传感器的磁敏传感器阵列。
5)  Hall sensors
霍尔传感器
1.
Rotor position measurement of permantent maglev heart pump by use of Hall sensors;
应用霍尔传感器测量无源磁浮心脏泵转子位置
2.
The system uses single chip micro-controller combining Hall sensors as predictive data acquisition system,which sends acquired data to PC via serial port,and then the PC analyzes,processes,displays and saves these data in LabVIEW environment.
该系统将单片机为核心的小系统,结合霍尔传感器作为前端的数据采集系统,将采集到的数据利用串口传送到PC主系统。
3.
In order to provide the convenience of simulation about integrated Hall sensors, magnetic field model and Hall model are build in Ver- .
可用于设计集成霍尔传感器的整体设计,将磁信号转换为电信号。
6)  Hall effect sensor
霍尔传感器
1.
By means of the sensitivity of the Hall effect sensor to geomagnetic field, the in.
在立轴支承的转盘中央安装一个平面反射镜,在转盘的圆周边缘处安装一个霍尔传感器。
2.
Presented the design and architecture implementation of AC servo control system for permanent magnet synchronous motor with sinusoidal flux distribution using linear Hall effect sensors as the motor feedback devices.
由于安装在永磁同步电机定子上的线性霍尔传感器的输出模拟信号与转子气隙磁场强度成比例,与反电动势同相位,通过使用线性霍尔传感器代替光电编码器和开关霍尔传感器,可得到转子的位置和速度信息;在此基础上,给出一种不需要在静止坐标系和旋转坐标系之间相互变换,可以在静止坐标系中直接产生相电流命令的磁场定向控制算法。
补充资料:霍尔电流电压传感器工作原理

直测式霍尔电流传感器


    原边电流Ip产生的磁通量聚集在磁路中,并由霍尔器件检测出霍尔电压信号,经过放大器放大,该电压信号精确地反映原边电流。


    磁平衡霍尔电流传感器


    原边电流Ip产生的磁通量与霍尔电压经放大产生的副边电流Is通过副边线圈所产生的磁通量相平衡。副边电流Is精确地反映原边电流。


    磁平衡霍尔电压传感器


    原边电压Vp通过原边电阻R1转换为原边电流Ip,Ip产生的磁通量与霍尔电压经放大产生的副边电流Is通过副边线圈所产生的磁通量相平衡。副边电流Is精确地反映原边电压。


    霍尔电流电压传感器特点 
   
    ◎ 直测式霍尔电流传感器(50A……10000A)


Ⅰ、测量频率: 0……50KHz


Ⅱ、反应时间: <7uS


Ⅲ、线性度: 1%


Ⅳ、电源耗电少


◎ 磁平衡霍尔电流传感器(1A……1000A)


Ⅰ、测量频率: 0……150KHz


Ⅱ、精度: 0.2%


Ⅲ、反应时间: <1uS


Ⅳ、线性度好: 0.1%


◎ 磁平衡霍尔电压传感器


Ⅰ、测量频率: 0……20KHz


Ⅱ、线性度好: 0.1%


Ⅲ、反应时间: 40uS


    使用传感器模块注意事项


    ◎ 传感器模块在使用时,应先接通副边电源,再接通原边电流或电压。


    ◎ 在选用传感器模块时,要根据测量范围、精度、反应时间及接线方式等参数,选用不同型号的传感器。


    ◎ 测量电流时,最好使用单根导线充满传感器模块孔径,以便得到最佳的动态性能和灵敏度。


    ◎ 传感器模块的最佳测量精度是额定值下测得的,当测量值低于额定值时,原边用多匝绕线,使总的安匝数接近额定值,从而获得最佳测量精度。


    ◎ 电流母线温度不得超过100度。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条