|
|
1) seismic tomographic profile
地震层析剖面
1.
By using four seismic tomographic profiles of nearly 8 000 km long across the Qinghai-Tibet Plateau, we obtained the crustal and mantle velocity images and seismic wave anisotropy over the depth down to 400 km, which revealed significant characteristics of the crust and mantle structure in the region.
通过横穿青藏高原近 80 0 0km长的 4条天然地震层析剖面 ,获得 4 0 0km深度以上的地壳和地幔速度图像及地震波各向异性 ,揭示了青藏高原 4 0 0km深度范围内的地壳和地幔结构特征。
2) seismic profile analysis
地震剖面分析
1.
The field profile observation,indoor geological profile analysis,seismic profile analysis and the fission-track dating were used to study the formation age of dustpan fault depression.
利用野外剖面观察、室内地质剖面分析、地震剖面分析以及裂变径迹年代学等方法对鲁西隆起和济阳坳陷箕状断陷的形成时代进行了探讨。
3) shallow seismic profile
浅层地震剖面
1.
The continuous field printing of shallow seismic profile with biggist breadth often can not be implemented without the help of suitable hardware.
在简述VC++打印函数和运行顺序的基础上,本文提出浅层地震剖面的多页打印和预览的VC++程序实现方法,指出剖面图像的分页处理要与图形映射模式相关联;由于打印和预览的设备环境不同,实现图形映射时必须采用不同的方法;根据打印程序运行时打印和预览过程存在的差异,指出进行预览的必要性。
4) seismic profile
地震剖面
1.
Geological interpretation of the seismic profile in Tarim Basin and tectonic evolution of this area
塔里木盆地地震剖面地质解释及其构造演化
2.
Demarcating through-well seismic profile with diplog is one of the important ways to improve the quality of seismic interpretation.
地层倾角测井标定过井地震剖面是提高地震成果质量的重要途径之一。
3.
In seismic description,it often traced geologic horizon in seismic profile and reflected the geologic information on corresponding seismic horizon.
在地震解释中,常常在地震剖面上追踪地质层位,并且将地质信息映射到相应的地震层位上,有时追踪某一地震层位的波峰,有时是波谷,多数时候都没能精确地确定地质层位的位置。
5) seismic section
地震剖面
1.
Fault analysis and fault correlation in seismic section;
地震剖面上的断层分析及相关意义
2.
Lithology prediction of 2-D seismic section by neural net work technique;
用神经网络预测二维地震剖面的地层岩性
3.
Application research of digital image processing method for improving signal to noise ratio of seismic section image;
利用数字图像处理技术提高地震剖面图像信噪比
6) high-resolution seismic survey
浅层地震剖面测线
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|