1) "in-situ" composite coatings
"原位"复合材料涂层
2) composite coating
复合材料涂层
1.
Cutting picker with high chromium Fe-based composite coating prepared by plasma surface metallurgy;
反应等离子表面冶金高铬铁基复合材料涂层截齿
2.
Microstructure and properties of plasma clad iron based cermet composite coating;
等离子熔敷铁基金属陶瓷复合材料涂层的组织与性能
3.
The Fe-based composite coating was attained with self-designed Fe-Cr-Ni-B-Si-C alloy powders by self-developed DC-Plasma-Jet surface metallurgical equipment.
利用自行研发的送粉等离子束表面冶金涂层设备及Fe-Cr-N i-B-Si-C系混合合金粉末在普通低碳钢表面制备了铁基复合材料涂层。
3) composite coatings
复合材料涂层
1.
Co-based alloy and its nano-oxide (nano-Y2O3 / Al2O3) composite coatings, deposited on Ni-based superalloy substrate by laser cladding are introduced.
在Ni基高温合金表面,激光熔覆钴基合金及其纳米氧化物颗粒复合材料涂层。
4) in situ composite
原位复合材料
1.
Study on the orthorhombic experiment of the AlN/ZL101 In Situ composite;
AlN/ZL101原位复合材料的正交实验研究
2.
In order to gain higher magnetic performance and solve air pollution problems in extraction process of Fe-Cr fibers,cupreous body of Cu-13Fe-2Cr in situ composite materials were corrupted by using chemical extraction.
为解决Fe-Cr纤维提取过程中容易造成空气污染的问题,使得到的纤维具有较高的磁学性能,采用化学萃取法腐蚀掉Cu-13Fe-2Cr原位复合材料中的铜基体,制备了Fe-Cr金属纤维;通过调整硝酸与双氧水比例抑制NO2的产生;通过改变清洗方式使纤维具有较高的磁性。
3.
Fe-Cr fibers were extracted from Cu-16Fe-2Cr in situ composite wires in 65% nitric acid.
Fe-Cr纤维由Cu-16Fe-2Cr原位复合材料硝酸法萃取得到。
5) in-situ composites
原位复合材料
1.
Microstructure and properties of Cu-Fe-Ag in-situ composites;
Cu-Fe-Ag原位复合材料的组织和性能
2.
Effects of micro-alloying on microstructure and mechanical properties of Cu-15Cr in-situ composites
微合金化对Cu-15Cr原位复合材料组织和性能的影响
3.
Non-isothermal crystallizations of the polycaprolactam chain segment grafted carbon fibre(CF)/monomer casting(MC) nylon 6 in-situ composites were investigated at different cooling rates by means of differential scanning calorimetry(DSC).
采用差示扫描量热(DSC)法,研究表面接枝聚己内酰胺链段的碳纤维(CF)/单体浇铸(MC)尼龙6原位复合材料,以及其在不同冷却速率下的结晶动力学特性;用Jeziorny法和Liu法对它们的非等温结晶动力学进行处理。
6) in situ composites
原位复合材料
1.
Preparation and properties of polylactide/nano-silica in situ composites;
聚乳酸/纳米二氧化硅原位复合材料的制备和性能
2.
The results show that In Cu-11Fe-4Cr in situ composites,E(Cu)
采用选择腐蚀技术,提取了Cu-11Fe-4Cr原位复合材料中Fe-Cr纤维,并测定了其电极电位。
3.
A series of in situ composites were obtained by melt blending thermoplastic resin polysulfone (PSF) and four thermotropic liquid crystalline polymers (TLCP) using three methosd: (1)extruded by melt index machine directly; (2)extruded by a single screw extruder; (3)blended the raw materials by a mixer first, then extruded by single screw extruder.
将热塑性树脂聚砜与４种自制的热致液晶聚合物熔融共混，制备原位复合材料，采用了３种制样方法：①毛细管直接法；②单螺杆直接挤出法；③先用混合机混合均匀，再用单螺杆挤出。
补充资料：原位
分子式：
CAS号：
性质：源于拉丁语。指在原来的，正常、自然的部位或位置。
CAS号：
性质：源于拉丁语。指在原来的，正常、自然的部位或位置。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条