1) generalized single point precise integration
广义单点精细积分法
2) meticulous integration of one point subdomain
单点子域精细积分法
1.
For solving three dimensional diffusion equation, a meticulous integration of one point subdomain is established.
建立三维扩散方程的单点子域精细积分法 ,并通过稳定性分析 ,表明单点子域精细积分法相对于差分法的优越性 。
3) single point precise integration
单点精细积分
1.
A single point precise integration method of two level four point explicit difference schemes with higher stability for dispresive equation;
色散方程的高稳定性两层四点显格式的单点精细积分法
4) Generalized local fine point
广义局部精细点
5) Generalized Integral method
广义积分法
6) precise integration method
精细积分法
1.
Investigation on the precise integration method in structural dynamics;
关于结构动力学中精细积分法的研究
2.
Increment-dimensional precise integration method for nonlinear dynam icequation;
非线性动力方程的增维精细积分法
3.
The high accuracy numerical solutions of the system are obtained using precise integration method.
在结构连续化假定的基础上,将内筒和外筒视为铁摩辛柯梁,同时考虑内筒和外筒的剪切与弯曲变形,建立了筒中筒结构协同分析的哈密顿对偶体系,导出了相应的状态空间方程,其系统矩阵具有辛矩阵的特性,可用精细积分法求该体系的高精度数值解。
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条