说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 平衡稳定条件
1)  the balance and steady condition
平衡稳定条件
1.
A simple method of the balance and steady condition of the isolated system;
孤立系统平衡稳定条件的简洁求法
2)  Equilibrium and stability condition
平衡稳定性条件
3)  stable equilibrium condition
稳定平衡条件
4)  stability conditions of equilibrium
平衡的稳定条件
5)  balance condition
平衡条件
1.
Analysis on the phase balance conditions and the chemical trend of certain element’s non-existence in a phase;
分析某一组分在某一相中不存在的相平衡条件及化学势
2.
To meet the needs of the two balance conditions of both argument and amplitude simultaneously, at least, two parameters should be adjusted.
交流电桥的平衡不仅取决于桥臂参数的性质,还取决于调节参数的选择,要同时满足幅值和幅角的两个平衡条件,至少需要调节两个参数来实现。
3.
When the oscillation is stabilized, the oscillatory balance condition should be abided.
振荡稳定后 ,要满足振荡平衡条件 ;但在接通电源后要建立起稳定的正弦振荡 ,电路又必须满足起振条件 。
6)  equilibrium condition
平衡条件
1.
The result showed that,if only the necessary but insufficient condition,the equilibrium condition,was adopted to deal with the infinite uncertain boundary condition,the solution to the stress was non-unique due to the fact that the boundary problem here was a mal posed mathematic problem.
通过两个典型的半无限体实例,对水平表面作用无限均布压力下弹性地基的应力和位移解答进行研究,结果表明:对边界条件不明确的无限边界仅采用解答的必要非充分条件——平衡条件来等效处理,其应力解答不是唯一的,因为此时该边值问题不是一个适定的数学问题。
2.
Using limit equilibrium condition,the paper analyzed plastic limit of Ring slab with simple inside and fixed outside support.
利用极限平衡条件,对内支座为简支、外支座为固支的环板进行了塑性极限分析,假定环板破坏时的塑性铰线为径环向,假定塑性铰线上的径向弯矩、切向弯矩均达到极限弯矩MP,根据力的平衡条件和力的边界条件,得出了环板极限状态时的内力计算公式,并通过试算得出了环板在不同的内外半径之比时,公式中的塑性铰线位置系数0ρ、1ρ的取值,使内支座为简支、外支座为固支的环板按极限状态设计时的计算问题大为简化。
3.
In this paper, it is pointed out that the element analysis, developed by Gibson et al, of honeycomb structures with walls in uniform thickness under in-plane shear load does not satisfy equilibrium conditions.
本文指出Gibson等提出的等壁厚峰窝结构在面内剪力作用下的单元分析不满足平衡条件。
补充资料:条件稳定系统
      以开环传递函数的增益值在某个范围内为条件才能保证稳定性的闭环控制系统。下图为条件稳定系统开环频率响应的奈奎斯特图的典型形状。图中ω为参变量频率。根据奈奎斯特稳定判据,当(-1,j0)点位于奈奎斯特曲线的A点和B点之间时,闭环系统是稳定的。通过减小增益值改变奈奎斯特曲线,使(-1,j0)点位于C点和B点之间,或加大增益值使(-1,j0)点位于A点和O点之间,都会导致闭环系统的不稳定。在工程实际中应尽可能避免采用条件稳定系统。系统元件特性的老化和输入信号过大引起的系统元部件的饱和,都会减小条件稳定系统开环增益值,从而使系统变为不稳定。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条