说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 检验的效
1)  power of tests
检验的效
2)  effect and power of test
检验的功效效率
3)  testing results
检验效果
1.
Study on improving testing results of BP neural networks;
改善BP网络检验效果的研究
4)  test power
检验效能
1.
Methods: Simulation experiments were made by SAS software,using the type Ⅰ error,type Ⅱ error,test power and test efficiency of five tests as the index of evaluation at equal variance or unequal variance situation,when sample size are equal or unequal,when large variance to large sample size or large variance to small sample size.
方法:采用 SAS软件编程 ,模拟方差齐或不齐、样本例数相等或不等、方差与例数顺向或反向等情况 ,分别采用 t检验、u检验、Satterthwaite法、Cochran- cox法及 Wilcoxon秩和检验进行检验 ,观察不同方法的 型误差估计值 (E )、 型误差估计值 (E )、检验效能以及检验效率。
5)  test efficiency
检验效率
1.
When F<1 occurs corresponded with a particular treatment,an ordinary researcher often neglects the fact that adjustment to MSerror may make use of information contained in the original data sufficiently so as to improve the test efficiency in multivariate ANOVA.
其余未参与误差调整的诸因素所对应的F值增大而P值减小,提示检验效率得以改善。
2.
Methods: Simulation experiments were made by SAS software,using the type Ⅰ error,type Ⅱ error,test power and test efficiency of five tests as the index of evaluation at equal variance or unequal variance situation,when sample size are equal or unequal,when large variance to large sample size or large variance to small sample size.
方法:采用 SAS软件编程 ,模拟方差齐或不齐、样本例数相等或不等、方差与例数顺向或反向等情况 ,分别采用 t检验、u检验、Satterthwaite法、Cochran- cox法及 Wilcoxon秩和检验进行检验 ,观察不同方法的 型误差估计值 (E )、 型误差估计值 (E )、检验效能以及检验效率。
3.
Using the type I error, the type II error and test efficiency of five methods as the index of evaluation.
方法用SAS软件编程,在计算机上模拟不同总体分布、参数相等或不等及样本含量相等或不等条件下,分别采用五种不同方法进行假设检验,评价它们的Ⅰ型误差估计值EⅠ、Ⅱ型误差估计值EⅡ及检验效率。
6)  Equivalence test
等效检验
1.
Following brief introduction of the equivalence test, a sample is given to exemplify its performance with EquivTestTM 2.
对等效检验进行了简要介绍。
2.
Interval hypothesis test is a new test method which is based on the traditional significance test and includes noninferiority test, equivalence test and superiority test.
它是基于传统显著性检验而发展起来的一种新的假设检验方法,主要包括非劣效检验、等效检验与优效检验。
补充资料:验收抽样检验和监督抽样检验标准


验收抽样检验和监督抽样检验标准
standards for acceptance sampling and audit sampling inspection

  扣nshou ehoUVa叩Jianyan he iiandu eh以JYang iianyanbi0Ozhun验收抽样检验和监督抽样检验标准(stands记sfor accepteLnce sampling and audit saznpling Ins侧沈-tion)有关抽样检验的中华人民共和国国家标准至1卯8年已达20个。其中验收抽样检验标准有巧个,它们是:①《逐批检查计数抽样程序及抽样表》(GBIT2828一1987),②《周期检查计数抽样程序及抽样表》(G田T282乡一1987),③《不合格品率的计量抽样检查程序及抽样表》(GBIT6378一1986),④《计数序贯抽样检查程序及表》(GBZT8()5l一1987),⑤《单水平和多水平计数连续抽样检查程序及表》(CBIT 5052一1987),⑥《不合格率的计量标准型一次抽样检查程序及表》(GBIT 8()53一1987),⑦《平均值的计量标准型一次抽样检验程序及抽样表》(GBIT 8()54一1卯5),⑧《不合格品率的计数标准型一次抽样检查程序及抽样表》(GB/T13262一1991),⑨《跳批计数抽样检查程序》(GWT13263一1卯1),⑩《不合格品率的小批计数抽样检查程序及抽样表》(GB/T 13么抖一I卯I),⑧《抽样检查导则》(G田T13393一1卯2),⑩《挑选型计数抽样检查程序及抽样表》(GBIT13夕场一l卯2),O《粒度均匀散料抽样检验通则》(G脚T 13732一l卯2),。(孤立批计数抽样检验程序及抽样表》(GBIT 1523乡一l更抖),0《计量截尾序贯抽样检验程序及抽样表》(GBIT l63()7一l型拓)。 监督抽样检验标准有5个,它们是:①《产品质量监督计数抽样程序及抽样表》(GBIT 14162一1卯3),②《产品质量平均值的计量一次监督抽样检验程序及抽样表》(GB/T 14灾盯一l臾抖),③《产品质量监督小总体计数一次抽样检验程序及抽样表)(CBITI,侣2一1卯5),④《产品质量监督复查程序及抽样方案》(GBIT163C盼一1性尧刹玉),⑤《产品质量监督计数一次抽样检验程序及抽样方案》(eBzTI科37一l期)。 在上述的抽样检验标准中,较有代表性的抽样检验标准是GBIT2828、GB/T132以、GBIT6378、GBlT8()54,月41,、侧,J
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条