|
1) lectostratotype section
新型剖面
2) New profile
新叶型剖面
3) Holocene stratotype section
全新统层型剖面
1.
Stratigraphic division and establishment of a formation for the Holocene stratotype section in the coastal plain of the Bohai Bay.;
渤海湾滨海平原全新统层型剖面地层划分与建组
4) new blade section
新剖面
1.
The two-dimensional section directly obtained by Eppler method is converted into a new blade section in three-dimensional case since they are significantly different from each other.
计算结果表明新剖面螺旋桨方案的空泡斗要比常规剖面的宽。
5) stratotype
['strætə,taip]
层型剖面
1.
In this paper, we propose the Chetougou section, 1 km to the north of the Xiejia village, Tianjiazhai Township, Huangzhong County, Qinghai Province, as the stratotype section of the Xiejian Stage.
谢家阶的层型剖面在青海省湟中县田家寨乡谢家村北1km处的车头沟,谢家阶对应于国际地层表中的海相Aquitanian阶,其共同的底界定义为古地磁ChronC6Cn。
6) stratotype section
层型剖面
1.
The present paper studies in detail the fusulinids from the stratotype section of the Huashibanian Stage.
本文详细研究了贵州盘县滑石板村滑石板阶层型剖面的类动物群 ,有 5属 2 6种及亚种 ,其中 1未定种。
2.
The stratotype section is located on the northern edge of Dibu Co ,Gyangrang Township,Coqên County,Tibet(lat.
层型剖面位于西藏措勤县江让乡敌布错北缘(E84°46',N30°51')。
3.
Ruyang Geopark is featured by dinosaur group fossils,granite landscape,and typical stratotype section.
汝阳恐龙化石群地质公园是一座以恐龙化石群为主,以花岗岩地貌景观、典型层型剖面为辅,水体景观与生态人文景观相互辉映的综合型地质公园。
补充资料:关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条
|