说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 弹复曲率
1)  spring-back curvature
弹复曲率
1.
It is concluded that,in the course of stretch bending and straightening,the elastic district thickness is reduced by less than 3%,the decrement of the bending moment is proportional to the square of the tension,the spring-back curvature.
所得结论为,在与反弯矫直相同反弯曲率条件下,弹性区厚度略有减小,其减小量小于3%;弯矩减小量与拉应力平方成正比,其弹复曲率也相应减小;弯曲变形的弹复过程中,部分纤维处于塑性流动状态,弹复曲率和延伸量大于以往研究结果;若弯矩与拉力同步弹复,则弯矩与拉力弹复可按线性关系计算。
2)  curvature springback
曲率弹复
1.
The effect of major parameters such as side pressure P, and relative bending radius R/H on curvature springback ΔR is studied, the law of interaction between P, R/H, ΔR and distribution and changing of tangential strain in deformation area is obtained, and thus, a scientific base is provided for design and modification of die and selection of technological parameters.
通过绕弯试验和应变分析,研究了绕弯工艺的主要参数侧压P和相对弯曲半径R/H对曲率弹复ΔR的影响。
2.
In this paper, effect of changeover bending and technological parameters on curvaturespringback is studied, the effect law between curvature springback and numbers of change-overbending, best change-over numbers and side-pressure is obtained, which is useful for design ofrotate bending technology and die.
通过试验与分析,探讨了换向绕弯方法及工艺参数对曲率弹复ΔR的影响。
3)  curvature before elastic restoration
弹(复)前的曲率
4)  crimp recovery rate
卷曲弹性回复率
1.
As the tension of the heat treatment rose,the crimp frequency and the crimp radius of the monofilament went down,the crimp elongation rate went down,the crimp recovery rate and the crimp modulus of the monofilament and multifilament went up.
结果表明:随着热处理张力的增加,单丝的卷曲数和卷曲半径减小,单丝和复丝的卷曲伸长率减小,卷曲弹性回复率增加,卷曲模量增加;随着热处理温度的增加,单丝的卷曲数增加,卷曲半径减小,单丝和复丝的卷曲伸长率减小,卷曲弹性回复率增加,卷曲模量增加;在温度100~120℃且张力较小的条件下进行热处理时,PET/PTT纤维的单丝和复丝的卷曲弹性较好。
5)  curve of re-spring
回弹曲率
6)  General toric surface
复曲率面
补充资料:半硬壳式弹体(见弹道导弹弹体)


半硬壳式弹体(见弹道导弹弹体)
semi-hard-shelled missile body

bQn yingkeshi dan桩半硬壳式弹体(semi一hard一shelled、ssilebody)见弹道导弹弹体。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条