说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 三维探槽
1)  3 D trench
三维探槽
1.
Our recent research on the large scale geological geomorphological mapping and 3 D trench excavation at Gaowanzi, Haiyuan fault has revealed that at least 7 paleoearthquakes have been occurred since Holocene.
对海原断裂高湾子地点进行大比例尺地质地貌填图和三维探槽开挖,揭示出7次古地震事件,除1920年地震外,它们的年龄分别为距今(10004±3196),(6689±169),(6120±505),(4208±577),(2763±372)和(1005±465)a;重复间隔分别为(3315±3200),(561±532),(1920±766),(1425±686),(1578±595)和(980±465)a。
2)  three-dimensional groove
三维槽型
1.
Predicting the up-curl chip breaking of three-dimensional groove inserts;
三维槽型断屑上向卷曲切屑折断预报
2.
The comparable experiments have been done between the two newthree-dimensional groove inserts: great rake insert, waved-edge insert and flat rake insert.
通过对两种新型三维槽型铣刀片-大前角铣刀片、波形刃铣刀片和平前刀面直刃铣刀片的铣削力进行对比实验研究,分别建立了直线刃和波形刃铣刀片铣削力的数学模型,并编制了计算机程序对铣削力进行了预测,其结果与实验结果的变化趋势符合较好,可用于铣刀片粮型的开发及优选。
3.
With the wide application of each type of three-dimensional groove insert, insert groove reasonable cho.
随着各类三维槽型刀片的广泛应用,合理选用刀片槽型并准确预报其切削性能成为解决上述问题的关键。
3)  3D groove
三维槽型
1.
People worked on research of 3D groove inserts for many years and got lots of important achievements.
可转位刀片优化其槽型可使其切削性能得到改善,多年以来人们对刀片的三维槽型进行了深入的研究,取得了很多重要的成果,但随着工业的发展不断对刀片的切削性能提出新的要求,本文对三维槽型刀片进行了较系统的实验研究、理论研究、产品开发和设计,其主要内容: 1。
2.
In the light of this situation, systematical experimental, theoretical research and numerical analysis about which heating density function & temperature field and their application for the milling insert with 3D groove are pro.
针对这种情况,本文对三维槽型铣刀片的受热密度函数与温度场及其应用方面进行了较为系统的试验研究、理论研究及数值分析。
4)  D probe
三维探头
1.
Objective To assess the value of 3 D probe usage in obstertric clinic.
方法 采用一体化三维探头扫查方式 ,对 10 2例孕妇进行三维重建。
5)  D range
三维探测
1.
The structure of 3 D range sensor system for unmanned vehicle is introduced.
研制了无人驾驶三维探测传感器系统,并讨论该系统中的几种关键技术。
6)  Three-dimensional exploration
三维勘探
补充资料:探槽
探槽
exploratory trench
    在地质勘探工作中,为了揭露岩层或矿体,在地表挖掘的沟槽。坑探工程之一。探槽一般采用与岩层或矿层走向近似垂直的方向,长度可根据用途和地质情况决定。断面形状一般呈倒梯形 ,槽底宽0.6米,通常要求槽底应深入基岩约0.3米,探槽最大深度一般不超过3米。槽口宽度B取决于槽底宽度b、槽深h和槽壁倾角θ。其计算公式为:B=b+2hctgθ。在浮土层中,探槽大多采用手工挖掘。在山坡和较硬的岩层中,采用松动爆破或抛掷爆破方法掘进,再用手工清理。探槽施工简便,成本低,应用较广。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条