说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 时间塑形
1)  temporal configuration
时间塑形
1.
Their temporal configuration merely stays on the technical le.
然而,由于没有哲学、美学乃至宗教信念作为思想支撑,新潮作家始终没有形成自己的时间意识,他们的时间塑形仅仅停留在技术层面,最终沦落为操纵时间的游戏。
2)  plasticizing time
塑化时间
1.
The investigations were made on the plasticizing properties of lignosulfnate and polystyrene blends with different factors like different amounts of lignosulfnate,plasticizer,compatibilizer and different temperatures with the maximal torque,balanceable torque and plasticizing time as the analytical index.
研究了以木质素磺酸钙(木钙)和聚苯乙烯为主要原料的流变学行为,探讨了以共混体系中最大扭矩、平衡扭矩和塑化时间为指标研究了不同木钙含量、增塑剂量和增容剂量在不同温度下木钙与聚苯乙烯的共混塑化情况。
2.
In the complex BaSt2/PbSt2 stabilizer system, the plasticizing time of RPVC becomes short with increasing .
结果表明,BaSt2,CaSt2能够促进RPVC的塑化,而PhSt2和ZnSt2却推迟RPVC的塑化;在复配BaSt2/PbSte稳定剂体系中,随着 BaSt2比例的增大,塑化时间缩短,但BaSt2与PbSt2按分子数1:1比率时,RPVC熔体粘度增幅较大。
3)  plastic time
塑性时间
1.
In order to overcome the limitations above,the new intrinsic time,which is named plastic time,is defined.
为此,给出新的内蕴时间——塑性时间的定义,旧的内蕴时间是塑性时间的特例。
2.
The definition of a plastic time is presented and the intrinsic time suggested by Valanis K C is that of a specific case.
提出塑性时间的定义,Valanis K C提出的内蕴时间是其特例。
4)  injection time
注塑时间
5)  heating plasticizing period
热塑炼时间
6)  formation time
形成时间
1.
It is shown from the experimental results that the specific capacity of Al foil is markedly increased by formation at 20V with pre-heat treatment and depositing nano-alumina films compared with the traditional formation process,in which the maximum extent for the increase of the specific capacity is near 30%,while the decrease of formation time is over 90%.
结果表明,铝箔沉积纳米氧化铝膜并进行适当热处理,在20V电压化成后铝箔的比电容比传统化成和预热处理后进行化成的比电容有显著提高,最大比电容提高幅度近30%,形成时间降低90%以上。
2.
The space potential distribution and the streamer formation time are chosen as control variables of the growth.
首先基于经典的流注起始判据,计算了棒-板间隙流注起始电压;选择空间电位和电子崩形成时间作为流注生长控制变量,结合泊松方程、电荷连续性方程和欧姆定律描述流注通道内部的电荷转移,仿真流注的持续发展过程;当流注到达板电极后,选择放电树枝中电位梯度最大的通道作为最后的主放电通道。
补充资料:北宋泼塑鱼形水丞
北宋泼塑鱼形水丞  北宋瓷塑珍品。1972年辽宁北票县北四家子村出土,辽宁省博物馆藏品。高9.4厘米、长14厘米。水丞塑制成一形象生动的鱼形,白胎,施颜色极淡青釉。鱼身鳞纹,无首,翘尾,鱼鳍扩大上卷,形成翅状,四周饰珍珠状圆粒,圈足。造型奇特,别致生动,制作精巧,胎釉细腻。是北宋瓷塑中独具一格的佳作,罕见。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条