1)  plasma electrolysis
等离子电解
1.
The milling-tool of high speed steel was re-treated using formamide alcohol amine electrolyte fluid phase,plasma electrolysis carbonitriding method in solution,and the metallographic specimen was prepared.
用甲酰胺-乙醇胺电解液体系、液相等离子电解碳氮共渗工艺对刃磨后的高速钢铣刀进行再处理,制成金相试样测定渗层厚度和硬度,并进行实切性实验。
2)  plasma electrolytic oxidation
等离子电解氧化
1.
Effects of NaF additive on oxide ceramic coatings formed on aluminum alloys by plasma electrolytic oxidation;
NaF添加剂对铝合金等离子电解氧化陶瓷膜形成的影响
2.
The plasma electrolytic oxidation (PEO) method for the decorative coating of aluminum alloy was investigated.
 对铝表面制备装饰膜的等离子电解氧化方法进行了研究。
3)  plasma
等离子体
1.
Combination of non-thermal plasma and heterogeneous catalysis for removal of low concentration benzene hydrocarbons in air;
非热等离子体与催化相结合去除气相低浓度苯系物
2.
Extraction and separation of intermediates in plasma degradation of benzene;
苯等离子体降解中间产物的萃取与分离
3.
Effects of energy injection on removal of benzene hydrocarbons in the air by discharge plasma;
能量注入对放电等离子体去除气相苯系物的影响
4)  plasma
等离子
1.
High efficient plasma welding technology and its application;
高效等离子焊接技术及其应用
2.
Cavitation erosion characteristics of Ni60+TiC plasma cladding layer;
Ni60+TiC等离子熔覆层的汽蚀特征
3.
Exergy analysis of thermal plasma reactor for coal gasification;
煤等离子气化反应器的火用分析
5)  plasma arc
等离子弧
1.
Effects of Ti-Mg on properties of plasma arc "in-situ" welding for SiCp/Al MMCs;
Ti-Mg对SiCp/Al复合材料等离子弧原位焊接性能的影响
2.
Usage and maintenance of welding and cutting machines(62)——Usage and maintenance of plasma arc cutting machine;
焊接与切割设备的使用和维修(六十二)——空气等离子弧切割机的使用与维修
3.
Strengthening planning for grooved surface with chromium-plating with plasma arc;
槽形表面镀铬层等离子弧强化工艺规划
6)  plasma beam
等离子束
1.
Fe-based alloy design in surface metallurgy by plasma beam;
等离子束表面冶金铁基合金的设计与研究
2.
Effects of compress argon arc plasma beam scanning on microstructure and composition of electroless Ni-P alloy layer;
压缩氩弧等离子束扫描对化学镀Ni-P合金镀层组织与成分的影响
3.
In view of the wear out of diesel engine cylinder liners,the high energy density plasma beam was applied to high speed scanning the liner surface of cylinder under atmospheric pressure and to make improvement treatment on the in-wall of cylinder liner partly so as to obtain the high hardness at hardened layer.
针对柴油机气缸套磨损失效现象,采用高能等离子束在常压下快速扫描气缸套内表面,对其进行局部硬化改性处理,获得了高硬度淬火硬化层。
参考词条
补充资料:电解食盐水溶液离子膜电解槽所用的膜材料之一
分子式:
CAS号:

性质:又称全氟羧酸-磺酸复合离子膜  Rf-COOH-Rf-SO3H  电解食盐水溶液离子膜电解槽所用的膜材料之一。使用时,将较薄的羧酸层面向阴极,较厚的磺酸层面向阳极,因而兼有羧酸膜和磺酸膜的优点。由于Rf-COOH层的存在,可阻挡氢氧离子返迁移到阳极室,确保了高的电流效率(96%),因Rf-SO3层的电阻低,能在高电流密度下运行,且阴极液可用盐酸中和,产品氯气中氧含量低,氢氧化钠浓度可达33%~35%。可在全氟磺酸膜上涂敷一层全氟羧酸的聚合物,或是将磺酸膜和羧酸膜进行层压,或是采用化学方法处理而制得的复合膜。现以采用化学方法处理者质量最佳。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。