1) chilled cast iron cam
激冷铸铁凸轮
1.
The wear resistance of chilled cast iron cams with different graphite contents in the chilled layer were studied through wear contrast test.
采用磨损对比试验 ,研究了激冷层中不同石墨含量激冷铸铁凸轮之间的耐磨性关系。
2) chilled cast iron camshaft
冷激铸铁凸轮轴
1.
The reasons causing various types of blowhole defects in the chilled layer of the chilled cast iron camshaft were analyzed based on the blowhole defect locations,defect morphologies and dimensions,and relevant proper countermeasures were proposed.
根据冷激铸铁凸轮轴激冷层气孔产生的部位和气孔的形态、大小,分析了各种气孔缺陷产生的原因并提出相应的对策。
3) chilled nodular iron camshaft
激冷球铁凸轮轴
1.
A sort of chilled nodular iron camshaft was developed by adopting resin-coated sand shell mould casting process.
开发了一种采用树脂砂壳型铸造的激冷球铁凸轮轴。
4) Cam shaft of low alloy cold hardening cast iron
低合金冷硬铸铁凸轮轴
5) chilled cast iron
冷激铸铁
1.
In order to eliminate the high content of ferrite structure in the outer layer with depth of 1 mm of the chilled cast iron camshaft produced in shell mould,an experiment with adding metal antimony into iron melt was conducted.
为消除用覆膜砂壳型铸造工艺生产的冷激铸铁凸轮轴主轴颈外表面1 mm左右深度内的大量铁素体组织,进行了在铁液中加入金属锑的试验,加入量(质量分数)分别为:0。
2.
The "black line" defect found on chilled cast iron camshafts was analyzed metallographically and found that the microstructure of defect zone consisted of pearlitic matrix and D-type graphite.
对冷激铸铁凸轮轴的"黑线"缺陷进行显微分析发现,缺陷区的基体组织为珠光体,石墨形态为枝晶点状石墨。
6) Chilled iron
激冷铸铁
1.
In room temperature,under load and continuous lubrication condition, malleable iron,wear resistant iron,naduar iron,chilled iron with 45 # steel can be employed;chilled with wear resistant iron;chilled with chilled iron comparative testing research friction-wear characteristics of chilled iron.
在室温、载荷及连续润滑条件下 ,用可锻铸铁、耐磨铸铁、球墨铸铁、激冷铸铁与 4 5 # 钢 ,激冷铸铁与耐磨铸铁 ,激冷铸铁与激冷铸铁对磨试验 ,研究了激冷铸铁的摩擦磨损性能 结果表明 ,激冷铸铁的摩擦系数与磨损量均小于可锻铸铁与耐磨铸铁 ,其摩擦系数波动在 0 。
补充资料：钨铁电炉出铁(吉林铁合金厂)
钨铁电炉出铁(吉林铁合金厂)
吻 他排由帕中桩了士朴屏人乙曰“
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条