说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 闭式镦挤
1)  Closed-die upsetting-extrusion
闭式镦挤
1.
Closed-die upsetting-extrusion process is a suitable method to forming this kind of component because component forme.
零件闭式镦挤成形是较为合适的加工方法,不仅可以满足零件的质量要求,而且可以节省材料和加工时间,降低加工成本。
2)  cold closed upsetting-extrusion
冷闭式镦挤
3)  close-die upsetting
闭式冷镦
1.
Taking the shaft of automobile gearbox as an example,a multi-step cold-forging technology for manufacturing the multi-diameter shaft on ordinary hydraulic presses by adopting open-die cold extrusion and close-die upsetting was stated.
以汽车变速箱二轴锻件为例,介绍了在通用液压机上采用开式冷挤压与闭式冷镦相结合的成形方法锻制阶梯轴的一种多工步冷锻工艺。
4)  Upset-extruding
镦挤
1.
Numerical Stimulation and Analysis on Defect in the Upset-extruding Process of Hollow Products;
本文运用有限元分析软件Deform,数值模拟了空心扁法兰件镦挤的成形过程以及成形过程中椭圆孔缺陷产生的过程。
5)  upsetting extrusion
镦挤
1.
By the analysis and comparison of upsetting extrusion and cold forging technology,the upsetting extrusion technology on the countersunk square neck bolt is introduced in the paper.
通过两种工艺方案中成型凹模受力情况的分析比较 ,说明用镦挤工艺生产沉头方颈螺栓 ,可降低镦锻力 ,提高模具寿命 ,保证零件质
2.
Based on summing up different kinds of technological process of precision forging of spur gear,a new upsetting extrusion process and pattern die are designed.
在总结各种直齿圆柱齿轮精锻工艺的基础上 ,设计了一种直齿圆柱齿轮镦挤精锻工艺和模具 ,并进行了实验和上限模拟。
6)  upsetting-extruding
镦挤
1.
For a heavy forging with bulge,the upsetting-extruding process can be adopted.
对带凸台的大型饼类锻件,可采用漏盘镦挤工艺进行生产。
2.
Owing to the disadvantages of the traditional process of austenitic stainless steel neck flange with a large hole,a new upsetting-extruding process with tubular billet was presented.
针对应用广泛的奥氏体不锈钢中间带大孔的高颈法兰类零件传统锻造工艺的不足,提出了一种利用管坯直接镦挤法兰的新工艺;用DEFORM-3D软件模拟了奥氏体不锈钢(0Cr18Ni9)法兰锻件的管坯镦挤成形过程。
补充资料:自动冷镦机、多工位螺栓自动冷镦机
代码:00468
设备名称:自动冷镦机、多工位螺栓自动冷镦机
型号规格:机制件杆部直径≥20mm
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB9166-88、JB/T3053-91
1、冲头夹持器模孔中心线对夹持器后支承面的垂直度(mm) 在100长度上
0.0080.010.015>0.015 
2、凹模座模孔中心线对凹模后座支承面的垂直度(mm) 在100长度上
0.0080.010.015>0.015 
3、冲头夹持器模孔中心线对滑块行程的平行度(mm) 在100行程上
0.0160.020.02>0.02 
4、滑块行程对机身上与凹模座贴合的垂直面的垂直度(mm) 在100行程上
0.0160.020.02>0.02 
5、工件头部对工件杆部中心线的偏移量(mm)
<0.200.20~0.250.25~0.30>0.30 
(二)生产率(件/分)
     
20mm
>807065<65 
30mm
>605045<45 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条