1) high yield-tensile ratio material
高屈强比材料
2) High Yield-tensile Ratio
高屈强比
1.
Effect of Oxygen, Nitrogen Contents on Structure and Properties of Martensitic Stainless Steel with High Yield-tensile Ratio;
氧、氮含量对高屈强比马氏体不锈钢组织和性能的影响
3) pressure enduring
高强材料
1.
To test their pressure enduring performance,the super high pressure generator,designed to produce blast wave pressure up to 20-30 MPa,was introduced.
该发生器由高强材料锻压、焊接而成,其结构主要由主体、后盖、测压环3部分组成,并在设计上保证了输出端连接的通用性和爆炸压力的均匀性。
4) high strength material
高强度材料
1.
Analyses performance and characteristic of high strength material of hydraulic support which are checked by testing and manufacture technology,to reduce weight,lower costs,enhance the reliability.
介绍了目前我国矿用液压支架结构件使用的材料 ,着重对液压支架高强度材料的性能、特点进行分析 ,并通过了生产试验、制造工艺进行了验证 ,减轻了重量 ,降低了成本 ,提高了可靠性。
2.
Based on the introduction of the present condition and development of new material,the article looks forward the appli- cable and developmental perspective of sealing material,damping material and high strength material in the design of modern torpedo.
军用新材料是新型武器装备的物质基础,是武器装备发展的关键,本文在简要介绍了当今一些军用新材料的现状和发展情况的基础上,着重展望了密封材料、阻尼减振材料以及高强度材料在现代鱼雷设计中的应用及发展前景。
5) yield ratio
屈强比
1.
Size, distributing, morphology and number of the MA island influencing yield ratio, yield strength and DWTT of the pipeline steel are introduced in the paper by analyzing influence of the MA island on mechanical properties in X70 and X65 pipeline steel.
通过力学试验研究分析管线钢X70、X65中重要组分MA岛对力学性能的影响,得出MA岛的尺寸、分布、形态、数量对管线钢的屈强比、屈服强度、落锤影响的规律。
2.
The results show that adding very small amount of niobium and titanium(microalloying elements) can increase not only the steel's tensile strength,but its yield strength and yield ratio as well.
结果表明:添加微量的Nb和Ti元素可提高钢的抗拉强度,同时也可提高钢的屈服强度和屈强比;锰过高或过低都会阻碍组织中马氏体的形成;适当增加硅可以提高钢的抗拉强度并降低延伸率。
3.
The influence of rolling process on the yield ratio was researched.
介绍了济钢ASP生产线焊瓶用HP295的开发轧制情况,探索了ASP生产线HP295钢带的轧制工艺对屈强比的影响。
6) low yield ratio
低屈强比
1.
Thermomechanical processing of cold forging steel with high strength and low yield ratio;
高强度低屈强比铆螺钢轧制工艺的研究
2.
By using zirconium (Zr) and titanium (Ti) micro-alloying, controlled rolling and moderate cooling rate in two phases zone after rolling, a construction steel with the characteristics of low yield ratio(YR≤0.
利用Zr、Ti进行微合金化,对钢板进行控制轧制并在轧后两相区适当快冷,获得了低屈强比(YR≤0。
补充资料：屈强
1.亦作"屈强"。 2.倔强。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条