1) Steel plate size
钢板尺寸
2) dimension of GFRP
玻璃钢板尺寸
1.
A finite-element analysis and tests are performed to discuss the effect of dimension of GFRP on ten RC beams strengthened by different length and thickness of GFRP,and discover the most optimal dimension with their strength enough,which is used for a base of optimization design of the same type beam.
对10片粘贴不同玻璃钢板长度和厚度的加固梁进行有限元分析和试验研究,探讨玻璃钢板尺寸对加固混凝土梁加固效果的影响,试图找到在满足加固要求的前提下的最佳玻璃钢板粘贴尺寸(即最佳的长度和厚度),为该类构件的优化设计奠定基础。
3) Dimension conformity rate
钢板尺寸合格率
4) ball size
钢球尺寸
1.
From the analysis on factors of impacting ball size,it is indicates that several impacting factors such as experienced formula or semi-theoretical formula have been comprehensively considered and the design for ball size has been conducted,thus the precise value gained.
从分析影响钢球尺寸的因素出发 ,指出运用综合考虑了多个影响因素的经验公式或半理论公式 ,对钢球尺寸进行设计 ,方能获得其准确值。
2.
Based on the ball size that was calculated to meet the requirement for lab test, a series of orthogonal tests were carried out to select parameters appropriate to the ball milling process.
研究了球磨参数对NiFe2O4尖晶石粉料的颗粒粒径的影响·通过计算确定了试验所需钢球尺寸,在此基础上,进行正交试验选择合适的参数·试验结果表明,球磨时间是影响粒径的主要因素,而研磨体级配对粒径分布范围有较大影响·确定合适的球磨参数为:球磨时间36h;研磨体级配35∶40∶25;料球比1∶2;球磨介质的体积分数为75%
5) Sheet sizes
板材尺寸
1.
Selecting proper sheet sizes can improve material utilization in the manufacturing of electrical machines.
通过选择合适的板材尺寸,可以明显提高电机铁心用硅钢片的下料利用率。
6) the size of bottom-slab
底板尺寸
补充资料：工程图标准尺寸及坐标尺寸
标准标注类型，是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。
· 3.2 标准标注到坐标标注的转换
注意： 转化为坐标标注的尺寸必须是线性标注的，下列尺寸不能转化为坐标标注：
- 被显示成线性尺寸的直径
- 中心线尺寸
- 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base.
- 选择作为参考基准线的尺寸
- 选择基准的引出线，该点为0点
- 选择 MOD DIM TYPE > Lin to Ord .
- 选择线性尺寸：注意：必须选择具有相同基准的尺寸
========>>>>
1. 选择 DIM PARAMS > Diam Dim Type .
2.点击Ord to Lin 
3.选择尺寸即可
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条