说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 板极设计
1)  the board-grade design
板极设计
2)  plate & grid design
极板与板栅设计
3)  Cathode design
阴极设计
1.
Integral impeller s formation upon Pro/E platform and cathode design;
基于Pro/E平台的整体涡轮造型及阴极设计
2.
According to the basic principle of electrochemical machining,discussed in this paper are two kinds of cathode design methods,which were respectively based on the mathematical model of a simplified electric field and the mathematical model of actual electric field distribution in the machining gap.
根据电解加工的基本原理,探讨了基于间隙内简化电场和基于间隙内实际电场分布数学模型的叶片电解加工阴极设计方法,对比分析了这两种阴极设计方法对间隙内电场强度分布的影响,通过一组工艺试验验证了阴极设计的精度。
4)  electrode design
电极设计
1.
Finally,an electrode design and calculation process is simulated on comput.
提出了一种加工复杂构型的整体涡轮通道的创新思路和六轴联动创成式电火花加工的成形原理及工具电极设计的方法 ,建立了电极设计中的数字仿真变分模型 ,论述了电极路径的求解方法及设计过程的干涉计算问题 ,在计算机上仿真完成了某一电极设计计算过
2.
To produce shrouded turbine blisk by electro-discharge machining(EDM),a special CAD/CAM system called the BliskCad/Cam is developed to solve the problems,such as electrode designing and manufacturing,searching path for multi-axis NC-EDM,and precision measurement and detection,etc.
该系统解决了电极设计与制造、加工轨迹搜索、加工仿真与精度检测等技术难题。
3.
This paper describes the optimum project of heating equiment and electrode design con- cerned, based upon the small-sized LTR heat treatment furnace with fluidized graphite bed which was early developed by the writers, and the experience of developing a large powered fur- nace thereafter.
本文以笔者早年设计的小型石墨流态床热处理炉(LTR)和随后研制大功率炉的经验,讨论加热装置的最佳方案和电极设计的有关问题,通过理论分析和试验,给出950℃以下的温度-电阻曲线和屏蔽电极区间的电压-幂次和电阻-幂次曲线。
5)  ultimate design
极限设计
1.
By the study on whole strength and parameter optimization for the bearing,the theory analysis and the test show that the ultimate design method can largely increase carrying ability and service life of the bearing without changing bearing material and manufacture technology,and the method can decrease bearing weight and reduce the material consumption.
通过对轴承整体强度空间的研究和参数优化 ,从理论分析和试验证明 ,在不改变轴承材料及制造工艺的条件下 ,“极限设计方法”能大幅度提高轴承的承载能力和使用寿命 ,且能有效地减轻轴承重量 ,降低材料消耗。
6)  anode design
阳极设计
补充资料:1350mm双流板坯连铸机(重庆钢铁设计研究院设计)


1350mm双流板坯连铸机(重庆钢铁设计研究院设计)


叠 135Omm双流板坯连铸机(重庆钢铁设计研究院设计)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条