说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> ARMA结构建模
1)  ARMA structural modeling
ARMA结构建模
2)  ARMA modeling
ARMA建模
3)  structural modeling
结构模建
4)  structure modeling
结构建模
1.
And summarized the principles for planning DSM in order to calculate large DSM by computer and insure the reliability of DSM planning result,an algebra method for DSM planning based on structure modeling is also presented,which have the advantages of versatility and easy implementation due to its strict mathematic derivation.
为了便于在计算机上进行大规模DSM处理,保证DSM规划结果的可靠性,还提出一种基于结构建模方法的DSM规划的代数方法。
2.
Hence in this paper, research task is based on "the 3-1) structure modeling and the development of software system about die design" , which have a great signif.
因此,以“挤压分流模具三维结构建模及其软件系统开发”为研究课题,对改善铝型材挤压模具设计手段与方法,提高设计效率,将设计人员从大量重复的手工劳动中解放出来,使他们有可能将时间投入到产品的研究与开发之中去,并为后续的铝型材挤压模具打下基础,具有重要的意义。
3.
This article aims to apply the Solid-works in the structure modeling of quartz flexure beam,and to imitate the moving process of quartz flexure beam in the-shock-response-spectrum-experiment via ANSYS,by which we can analyze the quartz flexure beam vibration response curve of pressure and resistance.
本文运用Solidworks对石英挠性梁进行结构建模,利用ANSYS模拟石英挠性梁在冲击响应谱试验中的运动过程,分析研究石英挠性梁的振动响应应力曲线,从而为石英挠性梁的应用环境提供技术参数,为相关产品的可靠使用提供理论依据和参考。
5)  structural modeling
结构建模
1.
The present structural modeling method is validated through ANSYS FEM software for the case of a composite box beam.
对于复合箱梁情形 ,目前的结构建模方法正确性通过ANSYS有限单元软件得到了验证。
2.
An improved method for structural modeling is then used to manage two types of knowledge unit, the knowledge of module design and that of module correlation.
针对模块化智能设计过程中,专家系统处理的重点和难点是大量的经验性、启发性领域知识的问题,对专家系统的核心部分——知识库的管理进行了研究,给出了面向模块的知识库组织策略,提出了一种知识库结构建模方法。
3.
The existing method for region partition in structural modeling is analyzed.
针对现有结构建模区域划分方法的不足,基于将拓扑分析转化为代数分析的原理,指出区域划分的实质是要构造某种等价关系,该等价关系是元素不可分的充要条件。
6)  modeling behaviors
建模结构
补充资料:凹模、凸凹模工作型面加工工艺过程
1)备料。 n
    2)锻造。锻成长方形的坯料(每件留长工艺夹头)。 n
    3)热处理。退火。   n
    4)铣(刨)削。铣(刨)削六面成长方形模块。 n
    5)磨削。磨削上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度。 n
    6)钳工加工。用平板和划线盘按图划线,并打样冲眼;用钻头钻螺纹底孔;用圆柱销孔的预孔;用钻头钻挡料销让位孔;用钻头在中心处钻穿丝孔等;正、反面孔口倒角;凸凹模用钻头孔扩,保证刃口高度;攻螺纹;铰孔。n
  7)铣削。平口钳装夹工件;用的立铣刀铣削型孔至尺寸,保证深度。 n
   8)热处理。凹模工件淬硬至HRC60~64,凸凹模工件淬硬至HRC58~62。 n
   9)平磨。磨上、下两端面及相邻两侧面,用90。角尺测量相邻两面的垂直度至图要求;退磁。 n
   10)线切割。按图编制线切割程序,切割模型孔成形,留单面研磨余量0.005 mm。 n
   11)钳工加工。研光线切割面: n
   12)检验。 n复合冲裁模的装配应选择凸凹模作为装配基准件,先装下模部分,后装上模部分
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条