说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 再造路径
1)  reengineering path
再造路径
2)  reengineering way
再造途径
3)  Path construction
路径构造
1.
Research and Implementation of Certification Path Construction Algorithm;
认证路径构造算法研究与实现
4)  path discovery
路径构造
1.
Even the topological simplification ofbridge CAs wasgiven,as cross certificate meshesgrow in size and complexity,the number of possible routes between points increases quickly,so that the time required for path discovery can increase beyond a tolerable delay for real-time operation.
当前基于PKI信任机制的交叉认证在路径构造时存在着一定的规模性问题,即使对桥CA进行拓扑简化,随着交叉认证网络大小和复杂度的不断增长,点与点之间可能路线的数量也在迅速增加,以使路径构造的需求时间超过了实时系统可以容忍的延迟度。
5)  path creation
路径创造
1.
Technological path creation based on interfirm innovation networks;
基于企业创新网络的技术路径创造
2.
Through analyzing the basic framework of RIN and its target and tasks,this paper puts forward two basic ways in breaking path dependency and realizing path creation.
通过阐述区域创新网络的构成、目标与任务,揭示出区域创新网络实现路径创造的两种基本途径,说明区域创新网络的构建与区域的路径创造是一个相辅相成的关系。
3.
Grounded on the analysis over the causes of decline of resource-oriented region,this paper suggests that the successful transformation of resource-oriented regions lies in the achievement from path dependence to path creation.
本文从对资源型区域衰退的原因分析入手,提出资源型区域的转变在于摆脱路径依赖,实现从路径依赖到路径创造的跨越。
6)  path-creation
路径创造
1.
Research on path-dependence and path-creation of technology innovation;
技术创新的路径依赖与路径创造研究
2.
In this paper,we first analyze the path-dependence and the path-creation of technology innovation, and clarify the fact that the path-creation present potential innovation power in contrast to the path-dependence which will lead to the inefficiency of technology innovation.
本文首先对技术创新的路径依赖和路径创造进行了分析,说明了路径依赖造成技术创新的低效率和路径创造呈现出强大创新动力这一事实。
补充资料:Pro/ENGINEER中复杂几何路径的数组阵列
 

1 引言



    Pro/ENGINEER是目前应用非常广泛的CAD/CAM软件,其功能非常强大。在Pro/ENGINEER中进行特征复制时, PATTERN(数组阵列)可以一次建立多个相同的特征,比COPY(复制)省时省力。



    在实际应用中,阵列的几何路径有规则的(如直线形、圆形等),也有不规则的(如平行四边形、椭圆形等)。对于规则路径,其生成较简单,如圆形路径,选取一周向驱动尺寸,输入阵列的增量与个数即可。下面以在基座上钻孔为例,介绍不规则几何路径的数组阵列。



2 设计实例



    首先,生成基座(如图1黑点表示孔的圆心位),其中心点位于Pro/ENGINEER中坐标系的原点,再钻出左上角的第一个孔(以基座的两条边为参考边,这两条边的交点为准原点)。然后进行数组阵列,产生其余的孔,依次选择“Pattern→General→Table”。





图1 黑点表示孔的圆心位



2.1 步骤一



    选择图1中的尺寸“40,55”作为“表格驱动阵列的驱动尺寸”,然后选“Done”。



2.2 步骤二



    选择“Add”,进行表的添加(输入一个表名如A),接着打开一个窗口,其中已有的文字均为注释语句,最后一行为:



    idx       d4(40.0)     d3(55.0)



    其中,idx表示这一列填的是序号,从1开始;d后的数字以实际操作中产生的为准,括号内数值为步骤1中所选驱动尺寸的值,可以看出该值的显示顺序与尺寸的选择顺序是对应的。



2.3 步骤三



进行表的录入,依次填入:
1 65   55
2 90 55
3 115 55
4 140 55
5 50 85
6 60 115
7  70 145
8 95 145
9 120 145 
10 145 145  
11 170 145
12 150 85
13 160 115



    其中1~4为上部右边的4个孔,5~7为左边3个孔,8~11为下部右边4个孔,12~13为右边剩余2个孔。



2.4 步骤四



    首先点击“File→Save”,并且进行保存。然后点击“File→Exit”,退出程序。之后执行“Done”即可进行阵列,如图2所示。


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条