2) grouting technology
注浆工艺
1.
Advanced small pipe grouting technology for tunnel construction;
隧道超前小导管注浆工艺探讨
2.
The following paper introduces the strengthening mechanism and effect of liquefied foundation treatment by compaction grouting method,illustrates its strengthening spheres and grouting technology,and discusses its suitability and treatment effect in the treatment of medium liquefied sand foundation, in order to popularize the application of the treatment method.
介绍了压密注浆法处理液化地基的加固机理及加固效果,对其加固范围和注浆工艺进行了详细阐述,并结合施工工程实践,论述了压密注浆加固处理中等液化砂土地基的适宜性和处理效果,以推广该处理方式的应用。
3.
Therefore reinforcement principles of karst roadbed are defined and the best grouting technology is developed for design and construction of the railway bed.
为此,施工和设计中确定了相应的岩溶路基加固原则,探索出最佳的注浆工艺,运用多种手段对注浆质量进行了全面检测,结果完全满足工程和环境的要求。
3) grouting technique
注浆工艺
1.
Also briefly discussed roadway borehole grouting techniques, as well as borehole water block up grouting process flow and parameters.
对矿井巷道钻孔注浆工艺进行了简要讨论。
2.
This paper introduces construction method of working pit and receiving pit,illustrates precast and hoisting of union coupling,proposes attentions of pipe jacking,discusses pipe jacking method and grouting technique after its construction,and illustrates surveying and control measures in the jacking.
介绍了工作井和接收井的施工方法,简述了管节的预制和吊装,提出了管道预进的注意事项,探讨了顶管顶进及施工结束后的注浆工艺,阐明了顶进中的测量、纠编控制措施。
4) grouting process
注浆工艺
1.
This paper deals with simply the design and construction of the grouting treatment project of coal-mining hollowed zone under Wulumuqi-Kuitun highway,and make profound analysis for some problems such asgrouting pressure,grouting process,additional agent and so on in design and construction,and put as ward some suggestions as reference for other similar projects.
简要论述乌鲁木齐—奎屯公路下煤层采空 区注浆治理工程的设计和施工 ,并对其中的一些问题 ,如注浆压力、注浆工艺、外加剂等作深入分析 ,并提出一些建议 ,以供类似工程参考。
5) grouting design
注浆设计
1.
Detailed introduction is made from grouting design,calculation,construction method,matters deserving attention in construction,quality inspection and other aspects.
结合工程概况,提出采用渗透式注浆方式作为加固防护方案,对其注浆设计计算过程、施工工艺、施工注意事项、质量检查等方面进行了介绍,并对其施工效果进行了评价,以供类似工程参考借鉴。
2.
The paper also briefiy introducd drilling and grouting design.
介绍采用地面打钻深孔注浆充填主、副井井壁后空硐,应用了深孔位防偏斜技术,深孔位套管技术等多顶新工艺、新技术,通过浆液高压挤压作用降低孔隙率,减少地层压缩,加固地层,防止井筒的突然破坏,文中对钻孔灌注浆设计进行重点介绍。
3.
This paper introduced the ground pre-grouting design and the key technical measures of construction through an engineering practice, and summarized some useful experiences.
本文通过实例介绍了地面预注浆设计和施工关键技术措施,总结了提高注浆效率、改进“三同时”建井工艺的有益经验。
6) TSS grouting technology
TSS注浆工艺
补充资料：电泳注浆成型
分子式：
CAS号：
性质：陶瓷浆料的成型方法之一。利用浆料中颗粒荷负电，在直流电场作用下向阳极运动而沉积在模型(阳极)上形成坯体的成型方法。此法可加快坯体形成速度，坯体较致密，可用于面砖，基板等的成型，但有时会因水的电解作用产生气泡，电场不均匀会造成坯体厚薄不均或脱模困难，故尚未得到广泛使用。
CAS号：
性质：陶瓷浆料的成型方法之一。利用浆料中颗粒荷负电，在直流电场作用下向阳极运动而沉积在模型(阳极)上形成坯体的成型方法。此法可加快坯体形成速度，坯体较致密，可用于面砖，基板等的成型，但有时会因水的电解作用产生气泡，电场不均匀会造成坯体厚薄不均或脱模困难，故尚未得到广泛使用。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条