说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 体内外模型
1)  in vitro and in vivo model
体内外模型
2)  in vitro in vivo correlation models
体内外相关性模型
3)  in vitro model
体外模型
1.
The in vitro model to study the direct nose-brain transport of drugs was built by using excised bovine olfactory mucosa and Franz diffusion chamber,with huperzine A and trybizine hydrochloride as the model drugs.
分离牛嗅黏膜,以石杉碱甲和盐酸锥双净为模型药物,用Franz扩散池,建立评价药物经鼻-脑转运的体外模型。
2.
Objective To study the dynamic changes of transendothelial electrical resistance (TEER) on our in vitro model of brain blood barrier (BBB) made from primary culture of BALB/c mouse brain microvascular endothelial cells (BMVEC), and to explore the relation between TEER and BBB permeability, and search for the best culture condition.
结论建立的BBB体外模型在形态学、电阻和通透性方面具备了BBB的基本特性。
3.
Organ culture of rat trigeminal ganglion is an ideal in vitro model for pathogenesis study and therapeutic target exploration of primary vascular headache
目的颈动脉血降钙素基因相关肽水平升高是引发血管性头痛发作的重要原因之一,本研究探讨血管性头痛的发生机制和药物作用靶点的理想体外模型。
4)  Model in vitro
体外模型
1.
Method (1)Established the model in vitro for the permeability of endothelium using small pool technique; (2)Researched the model′s transendothelial electric resistance (TEER) on CMEC and its permeability on radioiodinated 125 I bovine serum album (RISA),while contrasting with brain microvascular endothelial cells (BMEC) and pulmo microvascular endothelial cells (PMEC).
方法 (1)用小池技术建立起内皮细胞通透性的体外模型 ;(2 )研究该体外模型耳蜗微血管内皮细胞的跨细胞电阻及对12 5I 牛血清白蛋白的通透曲线 ,并与脑及肺的内皮细胞通透性进行对照。
2.
AIM To study the method of setting up model in vitro for the permeability of blood labyrinth barrier fromguinea pigs and the model s permeability.
目的 研究豚鼠血迷路屏障通透性体外模型的建立方法及其通透性特征 。
5)  In vivo model
体内模型
6)  rat bile duct internal and external drainage animal model
大鼠胆管经体外内外引流模型
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条