1) coaxial electrospraying(electrospinning)
同轴电雾化(电纺丝)
2) coaxial electrospinning
同轴静电纺丝
1.
The special attention is focused on the rapid development in the nanocomposite materials such as nanocapsules,core-shell nanofibers and hollow nanotubes or nanofibers by using coaxial electrospinning and coaxial electrospray in the recent couple of years.
简要介绍了基于电流体动力学射流技术的静电纺丝和静电喷涂的基本原理和发展过程,重点讨论了两种同轴射流技术———同轴静电纺丝和同轴静电喷涂技术的研究现状,包括纳/微米包囊、壳-芯结构的纳米纤维和中空纳米纤维或纳米管的制备。
2.
Al2O3/SiO2 coaxial ultromicro-cable was prepared by coaxial electrospinning technique using Al(NO3)3,C8H20O4Si,ethanol,polyvinylpyrrolidone and N,N-dimethylformamide as staring materials.
采用同轴静电纺丝技术,以硝酸铝、正硅酸乙酯、无水乙醇、聚乙烯吡咯烷酮和N,N-二甲基甲酰胺为原料,成功制备了Al2O3/SiO2同轴超微电缆。
3.
PAN/SiO2 coaxial fibers were prepared firstly by coaxial electrospinning using PAN as the core and SiO2 sol as shell,and then C/SiO2 coaxial fibers were obtained with an outer diameter of 1μm after oxidation and pyrolysis of the eletrospun fibers.
以SiO2溶胶为壳层,聚丙烯腈(PAN)溶液为芯层,采用同轴静电纺丝法制备了PAN/SiO2同轴复合纤维。
3) coaxial electrospinning
同轴电纺
1.
Nanofibrous membranes of rigid polysaccharides including chitosan,alginate or hyaluronic acid(HA) were obtained by coaxial electrospinning of their corresponding aqueous solutions(the inner dope) and PEO(M_n=6.
将壳聚糖、海藻酸钠或透明质酸配制成水溶液,聚氧化乙烯(PEO)溶解在二甲基甲酰胺(DMF)/H2O混合溶剂中,以上述两溶液分别作为内、外纺丝液进行同轴电纺制备成纤维膜,进而利用适当溶剂除去PEO外壳,得到纯多糖纳米纤维膜。
4) electro-spinning
静电纺丝
1.
Exploration of fabricating MAV foils using electro-spinning method;
静电纺丝法制备仿生MAV翼初探
2.
PVP/Gd(NO3)3·Eu(NO3)3 composite fibers were prepared by electro-spinning technique with Gd(NO3)3·6H2O,Eu(NO3)3·6H2O and PVP as starting materials.
6H2O反应制得前驱体溶液,采用静电纺丝技术制备了PVP/Gd(NO3)3。
3.
It is suggested that solid carbon nanofibers can be made by electro-spinning method.
指出静电纺丝技术可制得实心碳纳米纤维。
5) electrospinning
电纺丝
1.
Process analysis of fiber electrospinning;
电纺丝形成纤维的过程分析
2.
Electrospinning and Ultrafine Polymer Fibers;
电纺丝与聚合物超细纤维
3.
Experimental study of using electrospinning as wrapping materials for hydrogel orbital implant;
兔眼应用聚氨酯电纺丝作为水凝胶义眼台包裹的效果
6) electrospinning
电子纺丝
1.
Polyethylene glycol oxide nanofibers with the 9×10~5 molecular weight were successfully prepared by electrospinning.
通过电子纺丝技术成功制备了分子量为9×105的聚氧化乙烯纳米纤维,并讨论了纺丝液的浓度范围,分析了纺丝条件对制备纳米纤维的影响,探讨了不同剪切粘度的聚氧化乙烯溶液制备的纳米纤维的差异和形成原因。
2.
In recent years, the studies of the electrospinning technology more and more gets to pay attention, and a lot of research reports have been published.
电子纺丝是一种可能制备具有微细直径的纤维成形技术，本文介绍了电子纺丝技术的基本原理和电子纺丝成形工艺对纤维形态结构的影响以及电子纺纤维的应用前景等。
3.
Nanofibers can be prepared by electrospinning,by different assembling methods electrospun nanofibers construct uniqe functional morphology and structure.
电子纺丝能获得纳米级纤维,采用不同收集方法可以使纤维呈功能性形态结构。
补充资料：厂用电受电
厂用电受电
energizing of auxiliary power system
chongyongd一on sho一Jd一on厂用电受电(energizing of auxiliary powersystem)机组附属设备安装完毕后需通电试运行，所需厂用电源由外部供给，因此厂用电受电是调试工作开始的标志。 受电步骤新建电厂先由电力系统向变电站供电，再依次对高压起动/备用变压器、3~10kv厂用配电装置、厂用工作变压器及380V配电装置供电。扩建电厂因高压起动/备用变压器已经投人运行，故可利用它的电源对扩建的厂用配电装置等供电。 调试项目主要有:①用额定电压依次对空载线路、变电站母线、隔离开关、断瘩器、互感器、变压器及厂用配电装置等进行冲击合闸试验。有条件时.冲击合闸前应先进行递升加压试验。升压过程中注意检查各设备有无放电声及短路现象，发现问题及时处理后再进行升压。②检查三相电压应平衡，相序应正确，各段母线的相位彼此应一致。对配电装置供电时，有时会由于母线电容和与母线连接的电磁式电压互感器的电感相互作用而出现铁磁谐振，此时相电压升高，中性点明显位移。为消除谐振可在电压互感器的剩余电压绕组处并联电阻以去振。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条