说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 重要度相似关系
1)  importance degree similarity relation
重要度相似关系
1.
Rough set model based on importance degree similarity relation in incomplete information system;
不完备信息系统下基于重要度相似关系的粗集模型
2)  relational similarity
关系相似度
1.
Calculation method of relational similarity based on singular value decomposition
基于奇异值分解的关系相似度计算方法
3)  connectivity similarity relation
联系度相似关系
1.
This paper further extend under determinism of incomplete decision information systems and set-pair analysis ,which is rough set extension based on set-pair connectivity similarity relation .
本文针对几种已有在不完备决策信息系统下拓展模型的局限性,结合确定性理论和集对联系分析方法,得到更广泛的拓展模型-基于集对联系度相似关系的拓展模型。
4)  similarity degree of attribute importance
属性重要性相似度
5)  similarity relation
相似关系
1.
Similarity Relation of Model Experiment about Thermal Environment of Tunnel Inside;
隧道内热环境模型试验的相似关系
2.
Decomposition of Rough Set Based on Similarity Relation;
基于相似关系粗糙集的分解
3.
Set approximation and its interpretation on vagueness based on similarity relations
基于相似关系的集合近似及其含糊性解释
6)  similarity relationship
相似关系
1.
Further discussion on similarity relationship between stratified flow and uniform flow;
再论异重流和均质流动的一些相似关系
2.
Some similarity relationships between density flow and uniform flow in open channel;
异重流和均质流动的一些相似关系
3.
After discussing the major factors affecting model-based creep experiment and the rules to dispose in designing experimental model,the needed similarity relationship for constructing models is presented,then the similarity relationship of cambers due to creep between model and original is put forward based on creep expression in CEB-FIP Model Code 1990.
讨论预应力混凝土桥梁徐变模型试验主要影响因素及处理原则,提出了模型梁设计时需满足的相似关系;基于CEB-FIP(MC90)徐变模型,建立了模型梁与原型梁跨中徐变长期上拱的相似关系。
补充资料:车削时进给量与刀尖半径粗糙度的关系
车削时,刀尖半径与进给量、表面粗糙度的理论值存在一定关系,我们选择进给量时一般不应超过此值。

h=re-(re²;-(0.5×f)²;)0.5

h为残留高度,而:

Ra=(0.25~0.33)h


因此:
fmax=(Ra×re/50)½;

刀尖圆角
mm
圆刀片
mm
Ra/Rz µ;m
0.4/1.6 1.6/6.3 3.2/12.5 6.3/25 8/32 32/100
进给量 mm
0.2   0.05 0.08 0.13      
0.4   0.07 0.11 0.17 0.22    
0.8   0.10 0.15 0.24 0.30 0.38  
1.2     0.19 0.29 0.37 0.47  
1.6       0.34 0.43 0.54 1.08
2.4       0.42 0.53 0.66 1.32
  6 0.20 0.31 0.49 0.62    
  8 0.30 0.36 0.56 0.72    
  10 0.25 0.40 0.63 0.80 1.00  
  12   0.44 0.69 0.88 1.10  
  16   0.51 0.80 1.01 1.26 2.54
  20     0.89 1.13 1.42 2.94
  25       1.26 1.58 3.33
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条