1) post annealing temperature
真空退火温度
1.
The anisotropic magnetoresistance (AMR) of Ni_(81)Fe_(19) thin films deposited by RF magnetron sputteringsystem has been investigated on different thickness, substrate temperature, post annealing temperature.
我们研究了厚度、基片温度、真空退火温度对磁控射频溅射制备的Ni_(81)Fe_(19)薄膜各向异性磁电阻(AMR)的影响。
2) annealing
[英][ə'ni:liŋ] [美][ə'nilɪŋ]
真空退火
1.
Its property was dependent on the vacuum annealing temperature.
通过对退火后FeMn钉扎自旋阀磁性的研究表明 ,真空退火对自旋阀的性质有影响 。
3) vacuum annealing
真空退火
1.
Influence of vacuum annealing treatment on mechanical and tribological property of chromium-doped graphite-like carbon coatings
真空退火处理对掺Cr类石墨碳膜力学和摩擦学性能的影响
2.
Effect of vacuum annealing temperature on properties of GZO/Ag/GZO three-layer films
真空退火温度对GZO/Ag/GZO三层膜性能的影响
3.
X-ray diffraction (XRD) and metallographic microscope were used to study the phase and morphology of the thin films prepared in different vacuum annealing conditions.
以V_2O_5粉末为原料,采用无机溶胶-凝胶法制备了V_2O_5凝胶膜,先经过在空气中的热处理后再经过真空退火处理得到了以VO_2为主相的薄膜。
4) annealing temperature
退火温度
1.
Effect of annealing temperature on the microstructure of rapidly-solidified TiNi-Cu alloy ribbons;
退火温度对Ti_(53.5)Ni_(22.8)Cu_(23.7)合金快速凝固条带组织的影响
2.
Influence of annealing temperature on structure and properties of Al-6Mg-Sc-Zr alloy;
退火温度对Al-6Mg-Sc-Zr合金组织与性能的影响
3.
Effects of annealing temperature on microstructures and properties of the 25Mn-3Si-3Al-TWIP steel;
退火温度对25Mn-3Si-3Al-TWIP钢组织和力学性能的影响
5) anneal temperature
退火温度
1.
Effect of anneal temperature on performance of poly(chloro-p-xylylene)films;
退火温度对聚氯代对二甲苯膜性能的影响
2.
Taking original shape examination as contrast,the HT250 welding strain under three kinds of different anneal temperature(500℃、600℃、650℃)was studied.
以未进行退火处理试件为对比,研究了三种不同的退火温度(500℃、600℃、650℃)对HT250焊接残余应力的影响;对四块试件分别测试了各自的焊接应力,并将测试数据输入计算机得到了不同退火温度下的试件的焊接应力曲线;结果表明:此试验的最佳退火温度为650℃。
3.
The paper studies the effect of different cold deformation and anneal temperature as well as holding time on the material organization and property of alloy pipe 5086,sets the production process system of aluminum alloy 5086 at state of H34.
研究了不同冷变形程度、退火温度与保温时间对5086铝合金管材组织及性能的影响,确定5086铝合金H34状态的生产工艺制度,在工业生产条件下,其产品的技术指标达到了用户要求。
补充资料：软化退火(见低温退火)
软化退火(见低温退火)
soft-annealing
rU0nhUO tUihUO软化退火(soft一annealing)见低温退火。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条