说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 腐蚀控制步骤
1)  control step of corrosion
腐蚀控制步骤
2)  control step
控制步骤
1.
Analysis on pH value and control step in wet FGD(flue gas desulfurization);
湿法烟气脱硫系统的pH值及控制步骤分析
2.
The comparison of reaction rate, mass transfer rate and gas-liquid mixing rate indicated that the p-xylene oxidation process was controlled by the chemical reaction, and the control step was the oxidation of p-toluic acid to 4-carboxybenzaldehyde.
在典型的工业条件下,对二甲苯氧化过程为液相化学反应控制,控制步骤为对甲基苯甲酸生成对羧基苯甲醛的反应步骤。
3.
The transfer of sulphur in pig iron melt is the control step in the process,which is judged by theoretical analysis and verified then by experiment.
研究用CaO(w(CaO) =90 % ) +CaF2 (w(CaF2 ) =5 % ) +CaCl2 (w(CaCl2 ) =5 % )渣对铁水脱硫过程的动力学 理论分析判断和实验证实 ,该过程的速率控制步骤为硫在铁液中的传质 说明加强和改善搅拌 ,是提高脱硫效率的重要措
3)  controlling step
控制步骤
1.
Analysis of controlling steps study on absorption dilute gases of sulfur dioxide by sodium sulfide solution;
Na_2S溶液吸收低浓度SO_2的控制步骤分析
2.
Operating area of each controlling step in the reaction process is determined.
文章研究了盐酸用量和浓度、搅拌强度、颗粒粒度、反应温度对Al2O3浸出率的影响,确定了反应过程中各控制步骤的操作区间。
3.
By analyzing the kinetics steps of the gs reaction and the relationship between the original radius of particles and their reaction time,controlling step of the reaction is believed to be chemical reaction.
通过分析气—固反应的动力学步骤 ,以及原始颗粒半径与反应时间的关系 ,得出化学反应为此分解过程的控制步骤。
4)  corrosion control
腐蚀控制
1.
Experimental study on corrosion control using coking wastewater as circulating cooling water;
用焦化废水作补水的循环冷却水系统腐蚀控制实验研究
2.
The general idea of developing corrosion control of weapon equipment systematically in remanufacturing Engineering was outlined.
提出了系统性开展装备腐蚀控制再制造的思路。
3.
Based on the study of calendar life for the helicopter tail blades,three main corrosion causes are analyzed,and some suggestions on corrosion control are presented.
结合某型直升机的日历寿命研究分析了现役直升机的腐蚀情况,具体研究了引起腐蚀的三大原因,针对这些原因提出了相应的控制措施,对未来几年直升机腐蚀控制的研究提出了一些看法。
5)  Reaction controlling step
反应控制步骤
6)  Preston equation
控制步骤理论
补充资料:腐蚀控制步骤
分子式:
CAS号:

性质:腐蚀系统中,总的动力学过程是由若干单个过程依次相连组成的。腐蚀速度主要决定其中阻力最大的某一过程的反应速度,则这一过程为整个腐蚀的控制步骤。在研究腐蚀时,确定控制步骤,研究控制因素及控制程度,为寻找有效防腐途径有着重要意义。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条