1) internal evaporation (drying) rate
![点击朗读](/dictall/images/read.gif)
内部蒸发速率
2) internal evaporation (drying) rate
![点击朗读](/dictall/images/read.gif)
内部蒸发干燥速率
3) evaporation
[英][i,væpə'reiʃən] [美][ɪ,væpə'reʃən]
![点击朗读](/dictall/images/read.gif)
蒸发速率
1.
An experimental study on the evaporation of a small water droplet containing an additive on a heated, polished stainless-steel surface was performed.
研究表明,在给定的温度条件下,含醋酸钾和碘化钠的水溶液的平均蒸发速率要比不含添加剂的纯水慢。
4) evaporation rate
![点击朗读](/dictall/images/read.gif)
蒸发速率
1.
Investigation and analysis of the factors on evaporation rate under vacuum drying process
![点击朗读](/dictall/images/read.gif)
真空干燥过程中水蒸发速率的影响因素分析与研究
2.
Influence of evaporation rate on optical constants of ITO deposited by e-beam evaporation
![点击朗读](/dictall/images/read.gif)
蒸发速率对ITO光学常数的影响
3.
Theoretically,the formulas of the evaporation rate(NMg)and apparent mass transfer coefficiency(ka)of Mg were deduced.
在真空Ar气氛中精炼AM60镁合金熔体,测定了不同精炼条件下Mg元素的蒸发速率。
5) evaporate rate
![点击朗读](/dictall/images/read.gif)
蒸发速率
1.
It is discovered that technology parameters such as substrate temperature and evaporate rate have major influence on the origin of defect.
研究了不同沉积方式和工艺参数对沉积在K 9基底上的单层ZnS、Y bF3薄膜和多层ZnS/Y bF3薄膜缺陷的影响,发现基底温度和蒸发速率等工艺参数对缺陷的产生有较大的影响,太高或太低的基底温度和蒸发速率都会导致缺陷增加,采用电子束蒸发和蒸发源形状不同的阻蒸蒸发方式,缺陷密度分布有较大的差异。
6) evaporation velocity
![点击朗读](/dictall/images/read.gif)
蒸发速率
1.
The results suggested that the water evaporation quantity in the concrete became larger with the increase of w/c, and water evaporation velocity reached maximum value around two hours.
结果表明,轻骨料混凝土的水分蒸发量随水灰比增大而增大,且蒸发速率在2h左右出现最大值。
2.
Evaporation velocity was tested too,wicking velocity and evaporation velocity.
![点击朗读](/dictall/images/read.gif)
为了定量描述织物中水分传输过程中的两个关键因素——芯吸与蒸发的机制,确定影响织物吸湿快干性能的控制因素,采用精密电子天平组装了等液位分段快速响应毛细液体测试装置;并对3种织物的孔径分布与垂直于织物平面方向的芯吸速率进行了测量,对织物的蒸发速率进行了测试,分别比较了3种不同材质与结构织物的芯吸速率与蒸发速率,定量分析水分在织物表面蒸发的机制,分析了织物的孔隙率、平均半径、毛细管大小及孔径分布与织物蒸发速率的关系。
补充资料:内部蒸发速率
分子式:
CAS号:
性质:当利用连续式热气流干燥器干燥湿物料时,如物料的干燥速度低于临界湿含量,则干燥处于内部蒸发阶段,这时的干燥速率为内部蒸发速率。干燥多孔性物料时,在等速干燥阶段中,液态水的蒸发仅在物料表面上进行;在进入减速干燥阶段时,物料内部的液态水蒸发,物料内部进行蒸发的区域称为蒸发区。随着干燥的进行,内部蒸发区向外部扩展,形成干燥区。内部蒸发区中局部液态水的蒸发速率称为内部蒸发速率。
CAS号:
性质:当利用连续式热气流干燥器干燥湿物料时,如物料的干燥速度低于临界湿含量,则干燥处于内部蒸发阶段,这时的干燥速率为内部蒸发速率。干燥多孔性物料时,在等速干燥阶段中,液态水的蒸发仅在物料表面上进行;在进入减速干燥阶段时,物料内部的液态水蒸发,物料内部进行蒸发的区域称为蒸发区。随着干燥的进行,内部蒸发区向外部扩展,形成干燥区。内部蒸发区中局部液态水的蒸发速率称为内部蒸发速率。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条