1) phonograph connection
唱机连接
2) bonding mechanism
连接机理
1.
The anodic bonding mechanism between Kovar alloy and K4glass is analyzed and the effects of main technology parameters on bonding process are discussed.
分析了Kovar合金与K4玻璃阳极焊的结合机理和主要工艺参数对连接过程的影响,提出了金属与玻璃的连接机理为电场和温度场作用下的离子迁移、复合氧化物过渡层的生成和沉积,电压、温度、压力及试样表面质量是影响离子迁移和结合的主要因素,相匹配的热膨胀系数是防止开裂保证良好连接的必要条件。
2.
The bonding mechanism and interfacial reaction of LD31 aluminum alloy soldered with electric brush deposited Ni, Cu and then SnCu filler alloy were studied.
通过在LD31铝合金表面电刷镀Ni,Cu后再沉积SnCu钎料合金镀层的钎焊实验,研究了钎料镀层的连接机理及界面反应。
3.
The bonding mechanism of the vacuum hot roll bonding was discussed.
本文采用真空热轧焊接方法,进行了Ti6Al4V钛合金与0Cr18Ni10Ti不锈钢的连接试验,并分别对于无中间层和Cu中间层的焊接试验进行研究,测试了接头的拉伸强度,并利用光学显微镜、SEM、XRD对接头的微观组织进行了分析,讨论了真空热轧焊接的连接机理。
3) mechanical connection
机械连接
1.
The application of mechanical connection of reinforcement in structural engineering;
钢筋机械连接在结构工程中的应用
2.
Key points for mechanical connection and check of rebar joint;
钢筋机械连接的施工要点及接头检验
3.
Application of reeling rib rolled straight thread mechanical connection technology in Xinjiang area;
剥肋滚压直螺纹机械连接在新疆地区的应用
4) joi nt and mounting
机构连接
5) connecting mechanism
连接机构
1.
AM-50 type driving body connecting mechanism;
AM—50型掘进机机身连接机构
2.
A new self-reconfigurable modular robot DL-CubeII(Double L Cube) was developed,The DL-CubeⅡ adopted a small rotating hook connecting/disconnecting mechanism replacing internally balanced magnet mechanism in DL-CubeⅠ.
最后给出了硬件实验和几个仿真实验,验证了机器人连接机构的可靠性和自重构算法的可行性。
6) joining mechanism
连接机理
1.
And the joining mechanisms of the welding joints of mild steelaustenite stainless steel mild steelpure copper and nickeltungsten were analyzed,which lay a good foundation for further expanding th.
同时对低碳钢—奥氏体不锈钢、低碳钢—紫铜、镍—钨三种对接接头的连接机理进行了分析 ,为进一步扩大这一焊接方法的应用奠定了良好基础。
2.
In the same time, joining mechanismas of mild steel and austenitic stainless steel,mild steel and copper, nickel and tungsten are analyzed.
同时对低碳钢－奥氏体不锈钢、低碳钢－紫铜、镍－钨三种对接接头的连接机理进行了分析，为进一步扩大这一焊接方法的应用奠定了良好基础。
补充资料：唱机
1.留声机和电唱机的统称。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条