说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 单轴自动驾驶仪
1)  single-axis autopilot
单轴自动驾驶仪
2)  three-axis autopilot
三轴自动驾驶仪
3)  autopilot [英]['ɔ:təʊpaɪlət]  [美]['ɔto'paɪlət]
自动驾驶仪
1.
Error compensation with multiple sensors in a MEMS autopilot;
MEMS自动驾驶仪中的多传感器误差补偿
2.
Research on the Intelligent Fault Diagnosis Method of a Certain Missile Autopilot;
一种导弹自动驾驶仪智能故障诊断方法研究
3.
Development of autopilot technology of small UAV;
小型无人机自动驾驶仪技术
4)  automatic pilot
自动驾驶仪
1.
Design of breakdown diagnose fuzzy-expert system for shore-to-ship missile automatic pilot;
岸舰导弹自动驾驶仪故障诊断模糊专家系统设计
2.
An intelligent automatic pilot for the flight control of missiles by regulating is studied.
针对飞航导弹扇面发射和大空域机动飞行而引起的非线性时变等实际问题,根据飞航导弹弹道特性,运用智能控制理论及传统的反馈理论设计了一种基于专家系统的智能 PID 控制自动驾驶仪。
3.
A new data sampling and processing software developed by Visual C_(++) based on Windows operating system is introduced for automatic pilot auto-testing system which is made by oneself.
针对自行研制的自动驾驶仪自动测试系统,采用面向对象的编程方法,用VisualC++设计了基于Windows操作系统下的数据采集处理软件。
5)  missile autopilot
导弹自动驾驶仪
1.
Research of Using Aerodynamic/Reaction-jet Controller for Designing Missile Autopilot;
气动力/直接力复合控制导弹自动驾驶仪设计研究
2.
In this paper, the H∞ robust performance design method for the systems with mixed uncertainty is briefly introduced, and the problem of missile autopilot design is deeply studied.
简要介绍了复合摄动系统的H_∞鲁棒性能设计方法,并利用这种方法对导弹自动驾驶仪设计问题进行了研究。
6)  lateral acceleration autopilot
过载自动驾驶仪
1.
Inherent characteristic of lateral acceleration autopilot is studied.
对过载自动驾驶仪的固有特性进行了研究。
补充资料:卧式单轴、多轴自动半自动操作规程
适用机型:
1、 单轴自动车床:
CG110(1A10?),C1318(1A118),C1325(1A124),
C1336(1A136),A12,A20,A40。
2、 多轴自动、半自动车床:
C24·4(1240·4),C25·4,C2140·P4,C2150·4D,C2132·6D,C2132·6,
C24·6(1240·6),C2150·6D,C2216·6,BSA1/2 -4,1290,ANK135,
ANK155,1261M,1261?,1265·6,1265M·6,1240-0
一、认真执行《金属切削机床通用操作规程》有关规定。
二、认真执行下述有关补充规定:
(一) 工作前认真做到:
1、 检查分配轴及凸轮上的凸轮、撞块应完好无裂纹,安装正确,紧固牢靠。
2、 调正机床时,棒料、毛坯的夹紧,只准用手动不准用机动。
(二) 工作中认真做到:
1、 不准加工弯曲、未经冷拨和未经倒角的棒料。
2、 装料时须将料头对准夹头孔,轻轻击进。棒料长度一般以不超出料管200毫米左右为宜。
3、 四轴自动车床不准在第四工位上装料。六轴自动、半自动车床不准在第六工位上装料。
4、 保险键剪断时,就应查明原因,方准更换新键。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条