说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 固色处理
1)  colour fixing
固色处理
2)  cationic fixing agent treatment
阳离子固色剂处理
3)  solution heat treatment
固溶处理
1.
The effects of solution heat treatment processes on the microstructure and mechanical properties of the spray deposited 7090/SiC_P composite were investigated.
研究了固溶处理工艺对喷射沉积7090/SiC_p铝基复合材料的显微组织和力学性能的影响。
2.
It is thereby shown that the spinning and bulging forming can be done successfully, when taking four paths stepped spinning process, non-completed solution heat treatment (460℃±10℃ 30 min quenching by water) before spinning and completed solution heat treatment (515℃±10℃ 15 min quenching by water) before bulging for 6061.
结果表明,以6061铝合金为材质,采取4道次错距强旋成形工艺以及旋压前进行不完全固溶处理[(460±10)℃ 30 min、水淬]、胀形前进行完全固溶处理[(515±10)℃15 min、水淬],可确保旋压及胀形过程顺利进行,壳体的凹槽形状、尺寸精度、力学性能以及表面质量均可得到有效的保证。
3.
To dissolve the intermetallics which precipitated from the matrix of the layer, a solution heat treatment is conducted.
采用双层辉光离子渗金属技术 ,首先在低碳钢表面渗入合金元素钨、钼 ;然后作固溶处理 ,使金属间化合物溶于基体中 ;接着渗碳 ,使合金层内形成大量弥散、均匀、细小的合金碳化物。
4)  solution treatment
固溶处理
1.
Effect of solution treatment on the microstructure and properties of 0Cr17Mn11Mo3N steel prepared by metal powder injection molding;
固溶处理对注射成形0Cr17Mn11Mo3N钢组织性能的影响
2.
Effects of solution treatment on the microstructures and mechanical properties of Al-1.5Si-1.2Mg-0.6Cu-0.3Mn aluminum alloy sheets;
固溶处理对Al-1.5Si-1.2Mg-0.6Cu-0.3Mn铝合金组织性能的影响
3.
Effect of solution treatment on microstructure and properties of 7B04 aluminum alloy;
固溶处理对7B04铝合金组织和性能的影响
5)  solid solution treatment
固溶处理
1.
Effect of solid solution treatment on microstructure and properties of MIM Cr17Mn11Mo3N stainless steel;
固溶处理对注射成型Cr17Mn11Mo3N不锈钢组织性能的影响
2.
Effects of Y addition and solid solution treatment on microstructure and mechanical properties of AM60 magnesium alloys;
稀土Y及固溶处理对AM60镁合金组织和力学性能的影响
3.
Effect of the cooling rate during solid solution treatment on the properties of 1420 alloy;
固溶处理冷却速度对1420合金性能的影响
6)  solid solution
固溶处理
1.
Morphology Transformation of Eutectic Silicon in Al-Si Alloy during Solid Solution Treatment;
铝硅合金中共晶硅在固溶处理时的形态转变
2.
Effect of Solid Solution and Aging on Structure and Properties of 17-4PH Precipitation-Hardening Stainless Steel;
固溶处理和时效对17-4PH沉淀硬化不锈钢组织性能的影响
3.
Effect of Cu Content on the Behavior of Solid Solution Treated Al-Mg-Si Alloy;
Cu含量对Al-Mg-Si合金固溶处理行为的影响
补充资料:固溶处理
分子式:
CAS号:

性质:将合金加热到单相固溶体相区内,在适当的温度,保持适当的时间,使过剩相充分溶解到固溶体中,随后迅速冷却到室温,以获得过饱和固溶体。该处理后为时效处理做组织准备。铝合金、高温合金、铜合金、钛合金、镁合金和不锈钢,通过固溶处理达到预期目的,如固溶强化、消除铸态组织上的析出物,减少脆性、提高耐腐蚀性等。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条