1) film glue,glue film,gel membrane,pliofilm,jelly mould,rubber film
胶模
2) rubber mold
橡胶模具
1.
Novel design of rubber molding for air spring;
空气弹簧橡胶模具的独特设计
2.
First has outlined the rubber mold classification and the basic survey, analyzed the rubber mold to be in sole possession of the characteristic.
首先概述了橡胶模具的分类和基本概况,分析了橡胶模具的独有特点。
3.
The present status of rubber mold and the design of rubber mold are introduced.
介绍了橡胶模具目前的现状和橡胶模具的设计。
3) silicon rubber mold
硅橡胶模
1.
Based on rapid prototyping technology the silicon rubber mold for centrifugal casting is conveniently made.
硅橡胶模离心浇注装置结构简单 ,投资少。
2.
Due to the big cost of the silicon rubber and low speed on manufacturing the silicon rubber molds,this paper propose a optimized method that the mould cavity and adaptive filling blocks are manufactured simultaneously with the prototyping part.
针对在使用快速成形RP方法制造硅橡胶模中,硅橡胶成本昂贵,原型件制造速度慢的缺点,提出一种在使用RP设备加工RP原型件的同时,制造与之相配套的型腔与填充块方法,论述了相应工艺优化软件的关键技术。
4) jellium model
凝胶模型
5) molding model
封胶模具
1.
The surface treatments included electroplating hard chromium、ion-nitriding、and the newly developed ceramic hard film CrN, and compared the influence of different surface roughness on the pertormance of molding models surface roughness.
针对降低封胶模具与胶体间的粘模力来进行研究,以现在仍在使用的电镀硬铬、离子氮化,与蒸镀CrN陶瓷硬膜进行对比研究,探讨了不同表面粗糙度对封胶模具特性的影响。
6) plastic and rubber mold
塑胶模
1.
This article primarily analyzes the practical shortcoming of the current formula of plastic and rubber mold's shaping dimensions, and fully describes the influence the accuracy of the plastic and rubber dimensions on caused by its raw materials waving of contracting possibility.
在初步分析现有塑胶模成型尺寸计算公式在实际使用中存在不足和充分考虑塑胶收缩率波动对塑胶尺寸精度影响的基础上 ,从概率论的角度出发 ,提出了一种较为科学的修模余量的计算方
参考词条
补充资料：高温模量粘胶纤维
分子式：
分子量：
CAS号：
性质：又称富纤。一种在湿态下弹性模量较高的纤维。断裂强度较普通粘胶纤维为高的短纤维。延伸度较低，接近于棉。用质量较高的纸浆为原料，工艺过程也较为严格控制。用途与普通粘胶纤维相同。
分子量：
CAS号：
性质：又称富纤。一种在湿态下弹性模量较高的纤维。断裂强度较普通粘胶纤维为高的短纤维。延伸度较低，接近于棉。用质量较高的纸浆为原料，工艺过程也较为严格控制。用途与普通粘胶纤维相同。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。