说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 阔面铣刀
1)  slabbing cutter; slabbing mill
阔面铣刀
2)  ball end cutter
球面铣刀
1.
The process to grind ball end cutter is the most complex in all the tool grinding processes, especial for the rake faces and flank faces of the cutter.
前刀面与后刀面的刃磨加工是球面铣刀加工工艺中最复杂的加工模型 ,尤其是球面端刃的前后刀面的加工模型 ,是研究的热点问题 。
2.
A manufacturing model for the ball end cutter is presented, and the feasibility of grinding ball end cutters of different sizes using the same mechanism is discussed.
文中给出球面铣刀的制造模型 ,探讨了运用同一机构磨制邻近规格的不同球面铣刀的可行性问题 。
3)  face milling cutter
面铣刀
1.
Through a cutting experiment of milling 0Cr13Ni5Mo stainless steel, some cutting performances of two kinds of carbide face milling cutters such as tool life, effectiveness of chip forming and dividing and dynamic effect of process system are analyzed and investigated.
通过铣削 0Cr13Ni5Mo不锈钢的切削试验 ,对两种硬质合金面铣刀的切削寿命、卷屑和分屑效果、对工艺系统的动态影响等切削性能进行了分析研究 ,结果表明两种面铣刀在不同切削条件下具有不同的切削性能 ,分别适用于粗铣和半精铣加
2.
The limitation of cutting calculation for face milling cutter of M.
分析了克郎聂伯尔格解析法对面铣刀切入计算的局限性,提出了一种更为准确的计算方法,不仅能计算前刀面上最先接触的点,而且能更为准确地求出各特征点接触的先后顺序。
3.
With the face milling cutter as example, the mathematic model of milling by a face milling cutter was established and the simulation algorithm of the micro geometrical texture of the milling surface by a face milling cutter was proposed.
以面铣刀为研究对象,通过建立了面铣刀加工数学模型,给出了面铣刀铣削表面微观几何形貌仿真算法,并开发了相应的铣削表面形貌仿真系统。
4)  face milling cutters
端面铣刀
5)  face-milling cutter
面铣刀
1.
Because the programming process of numerical control program for high speed milling cutters is quite complex and hard to control, and also, the workload is comparatively heavy, this paper developed CAM modules for high speed face-milling cutters based on UG platform.
针对高速铣刀数控加工程序编制过程繁琐、工作量大、难于掌握等现状,开发了UG平台下的高速面铣刀CAM模块。
6)  milling cutter
面铣刀
1.
High-speed milling cutter is one of the most important techniques used to achieve the high-speed milling processing.
本文以已有的高速铣刀安全性的研究为基础,根据高速铣刀安全性国际标准,采用有限元分析方法对高速面铣刀的失效形式及其影响因素进行了分析和讨论。
2.
The milling cutter whose main declination was 45° was frequently used in processing of producing products.
主偏角为45°的可转位面铣刀是生产加工中经常使用的刀具。
补充资料:常绿阔叶落叶阔叶混交林
出现于亚热带和暖温带的过渡带或亚热带山地常绿阔叶林上界的森林植被类型。由常绿阔叶树和落叶阔叶树混合组成。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条