1) gas cutter
瓦斯切断器
3) gas examining instrument
瓦斯检器
4) gas sensor
瓦斯传感器
1.
Experimental of an infrared gas sensor based on infrared absorption spectrum theory in laboratory;
基于红外光谱吸收原理的红外瓦斯传感器的实验
2.
Research on failure mode and diagnostic method of gas sensor;
瓦斯传感器的故障模式与诊断方法研究
3.
Method of gas sensor fault detection based on SVR
基于SVR的瓦斯传感器故障诊断方法
5) methane sensor
瓦斯传感器
1.
Nonlinear correction of methane sensor based on improved BP neural network;
基于改进型BP神经网络的瓦斯传感器的非线性校正
2.
Application of infrared remote control to methane sensor;
红外遥控在瓦斯传感器中的应用
3.
No-blind-zone placement of methane sensor based on monitoring coverage;
基于监测覆盖范围的瓦斯传感器无盲区布置
6) gas burner
瓦斯燃烧器
1.
Numerical simulation of the length of turbulent diffusion flame of a gas burner;
重整炉瓦斯燃烧器火焰长度数值研究
2.
Furnace geometry and mesh of simulation domain were created with special structural gas burner.
采用计算流体力学方法以某种新型乙烯裂解炉辐射段为几何模型,保留特殊结构的瓦斯燃烧器原型未作简化,对计算域进行几何建模和网格划分,用标准的k-ε湍流模型、双δ概率密度函数扩散燃烧模型和蒙特卡洛辐射传热模型对炉内的燃烧和辐射状况进行三维全尺寸数值计算,以研究炉膛内的燃烧、传热和烟气流动情况。
3.
A V-shaped flame holder with many orifices used in a gas burner was developed.
提出了一种多孔V形瓦斯燃烧器稳焰块,对其稳焰特性进行了研究,并进行了燃烧试验。
补充资料:4925芯骨切断机操作规程
1、遵守铸造设备通用操作规程。
2、检查设备上的行程开关和碰块的位置是否正确,如不正确,必须调正。
3、工作前,用手扳动皮带轮,检查冲头上下运动是否轻便,如有卡住或沉重情况,应通知维修人员修理。
4、所切金属丝直径不得大于8毫米。
5、工作后,取下机床上未切完的金属丝。
6、工作后,擦净机床,加油保养导轨。
2、检查设备上的行程开关和碰块的位置是否正确,如不正确,必须调正。
3、工作前,用手扳动皮带轮,检查冲头上下运动是否轻便,如有卡住或沉重情况,应通知维修人员修理。
4、所切金属丝直径不得大于8毫米。
5、工作后,取下机床上未切完的金属丝。
6、工作后,擦净机床,加油保养导轨。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条