1) distribution of pressure,pressure distribution
压力分布<冶>
2) distribution of pressure
压力分布
1.
This paper provides a principle optimizing the coat hanger die with the tear shape manifold and a method simulating the distribution of pressure in the die cave.
阐述了泪滴型歧管衣架机头流道优化计算原理和压力分布模拟计算的方法 ,编制了CAE软件包。
2.
According to the mechanism and pressing process of sintered NdFeB magnet,the distribution of pressure during pressing process was analysed and derived,which is helpful to determined the pressing direction and the size of mold.
根据烧结钕铁硼永磁材料压制成型机理及压制成型工艺,分析了压制成型过程磁粉受力情况,推导出压制成型的压力分布公式。
3.
A principle optimizing the L die with the genetic algorithms and a method simulating the distribution of pressure in the die cave are provided.
讨论了L型机头流道主要参数对挤出压力分布均匀性的影响 ,并将本计算模块应用于工业实践。
3) pressure distribution
压力分布
1.
Calculation of pressure distribution in intermittent producing test well with δ Function;
利用δ函数计算间歇试采井压力分布
2.
Subjective assessment of pressure distribution for sports underwear;
运动内衣压力分布的主观评定
3.
Exact and simple method for calculating pressure distribution in deep gas condensate well with high temperature and pressure;
深层高温高压凝析气井压力分布的简便算法
4) pressure distributing
压力分布
1.
The method to calculate pressure distributing of ultra-thin gas film;
超薄气膜润滑压力分布的计算方法
2.
The results show that the inclined walls and the change of attack angle have great influence on the pressure distributing and St.
结果表明,倾斜壁面和攻角改变对压力分布和St有较大影响。
3.
On the basis of the differential equations of fluid momentum and its mass continuity equation, turbulent pressure distributing function is derived with regard to fluid inertia force.
从运动流体的动量微分方程及其质量连续性方程出发 ,分别采用紊流短轴理论和层流长轴理论来分析挤压阻尼器油膜层和滑动轴承油膜层 ,推导出油膜层压力分布函数 。
5) pressure distributions
压力分布
1.
To eliminate hydraulic valves noise pressure distributions,cavitation and noise spectrum inside different throttling grooves were studied.
为了消除液压阀中的噪声,对不同节流槽内部压力分布、气穴形态和噪声频谱进行了研究。
2.
On the basis of analyzing three cavity flows,and through the comparison of pressure distributions on cavity flows,it can be seen that the flowfield structure features and the effect of crucial parameters(L/D、W/D、δ_c、δ_h and M) on cavity flowfield structures.
在分析了弹穴3类流动的基础上,利用风洞试验着重研究了弹穴的几何参数(L/D、W/D、cδ、δh)以及飞行参数(M)与弹穴内流场结构间的耦合关系,获得了亚跨超声速来流条件下弹穴底面中心线上的压力分布及弹穴流动特性。
3.
The three-dimensional pressure distributions and temperature field of capillary-compensated,water-lubricated hydrostatic journal bearings with four deep recesses were analyzed.
研究得到了在水介质润滑下的动静压轴承三维压力分布、温度场分布及动特性系数。
6) paleo fluid pressure distribution
古压力分布
补充资料：融融冶冶
1.美好艳冶。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条