1) pore-creating material,pore forming material
造孔剂<冶>
2) pore-forming agent
造孔剂
1.
Effect of pore-forming agents content on bending strength of SiC/Al composites;
造孔剂含量对SiC/Al复合材料抗弯强度的影响
2.
Effect of pore-forming agents on mechanical properties of metal-bonded diamond wheels
造孔剂对金属结合剂金刚石磨具力学性能的影响
3.
In this paper, the porous silica ceramic materials and parts are fabricated by introducing the pore-forming agents into the materials by pelletizing method, aging the slip in the vacuum conditions and casting the slip under pressure.
通过造粒的方法引入造孔剂,采用真空抽气混合料浆及加压浇注的方法来制备多孔石英陶瓷材料及其部件。
3) pore former
造孔剂
1.
Effect of the pore former on the performance of air electrode;
造孔剂对空气电极电性能的影响
2.
The effect of mechanics of different pore former on the properties of low weight high insulation sintering product
不同成孔机理造孔剂对轻质保温烧结制品性能的影响
3.
The porous SiC ceramics were prepared by vacuum sintering in this investigation,the effect of different sintering aids,Al2O3-Y2O3 and Si,and different pore formers,acrylamide copolymer and Carboxymethyl Cellulose(CMC) on the microstructures and porosity were studied.
采用真空烧结方法制备了SiC多孔陶瓷,研究了不同助烧结剂Al2O3-Y2O3、Si以及不同造孔剂丙烯酰胺聚合物、羧甲基纤维素(CMC)对SiC多孔陶瓷形貌和气孔率的影响。
4) pore forming agent
造孔剂
1.
Influence of pore forming agents on the performance of membrane electrode assembly in PEMFC;
造孔剂对PEMFC膜电极性能的影响
2.
High specific surface area silicon carbide(SiC) was synthesized using citric acid(CA) as the pore forming agent by the tetraethoxysilane (TEOS) sol-gel and carbothermal method.
以柠檬酸为造孔剂,利用硅酸乙酯溶胶-凝胶和碳热还原法制备出了高比表面积的纳米碳化硅(SiC)粉体。
3.
In this experiment,diatomite and pore forming agent are used as main materials,half dry press mold,general sintering,a series cost-effective porous ceramics were produced.
本实验以硅藻土为主要原料 ,天然有机细粉为造孔剂 ,水玻璃为高温粘合剂 ,经半干压成型 ,常规烧成 ,制出了性能优良的硅藻土多孔陶瓷 ,随着造孔剂的加入量、烧成制度的改变 ,气孔率从 47%增加至 71 % ,最大孔径也随之从 1～ 1 0 μm变化 ,密度从 1 。
5) pore-making agent
造孔剂
1.
Effect of pore-making agent on properties of porous alumina ceramic;
造孔剂对多孔Al_2O_3陶瓷性能的影响
2.
Fabrication of Porous Al2O3 Ceramic Using Different Pore-Making Agent
利用不同造孔剂制备Al_2O_3多孔陶瓷
3.
The effects of the pore-making agents content on the porosity of SiC/Al porous preform produced by pressureless infiltration technique were investigated.
本文采用无压浸渗法制备了SiC/Al复合材料,研究了造孔剂含量对多孔预制体孔隙率的影响。
6) pore-forming material
造孔剂
1.
The low grade oil shale in the Nongan area,Jilin Province as a main material,turfs as pore-forming material,volcano dregs as additive and fly ash as intensifier were selected at ratio of 50∶25∶15∶10(oil shale∶turf∶voicano∶fly ash) and sintered at 1 050 ℃ by extrusion molding.
利用油页岩自身燃烧放出气体后形成孔洞的特性,以吉林省农安地区低品位油页岩为基料,以泥炭为造孔剂、火山渣为添加剂、粉煤灰为增强剂,选用配比为50∶25∶15∶10(油页岩∶泥炭∶火山渣∶粉煤灰),采用湿压成型,在1 050℃下烧结出新型的多孔建筑陶瓷。
补充资料：造冶
1.冶炼铸造。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条