说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 择一属性
1)  alternative attribute
择一属性
2)  attribute selection
属性选择
1.
Research on Attribute Selection Algorithm Based on Classification Theory of Corelation between Attributes;
基于属性间相关性分类理论的属性选择方法研究
2.
This method cam minimize the attribute selection,and keep the ability to classify tax data without great changes.
该算法解决了原有基于属性重要度的启发式属性约简算法结果中存在冗余属性问题,实现了属性选择较小化,并保持原有数据分类能力不发生大的变化。
3.
At the same time,the solution using attribute selection and instance selection to realize the approximation mining is brought out,and the mining efficiency and result model.
同时,提出使用属性选择和实例选择方法实现近似挖掘的方案,并对该方案进行挖掘效率和结果模型准确性的分析评估。
3)  feature selection
属性选择
1.
Improved BP neural network feature selection method
一种改进的BP神经网络属性选择方法
2.
Feature Selection Method Based on Fractal Dimension and Ant Colony Optimization Algorithm
基于分形维数和蚁群算法的属性选择方法
3.
A feature selection measure was defined to increase the classification rate and the purity of each sub-database.
利用粗糙集理论,从提高分类正确性和子数据库纯度的角度出发,提出了属性选择量度和分解过程终止量度。
4)  Attributions selection
属性选择
1.
Study on Attributions Selection and Rule Extraction of Data Mining for Classification Based on Neural Networks;
基于神经网络的分类数据挖掘属性选择和规则抽取研究
5)  attributes selection
属性选择
1.
This paper presents a method of neural network attributes selection based on data attribute importance ranking.
文中提出一种基于数据属性重要性排序的神经网络属性选择方法。
6)  alternative theorem
择一性
1.
The saddle point type necessary and sufficient conditions are obtained by an alternative theorem under a weakly convex condition.
然后,在较弱的凸性条件下,利用含矩阵和向量约束的择一性定理,建立多目标半定规划的互补弱鞍点和G-鞍点充分必要条件。
2.
We will establish a serial of alternative theorems involving matrix equations on the basis of interior product of symmetrical matrix.
在对称矩阵内积的基础上建立一系列含矩阵的方程的择一性定理 ,并在此基础上研究以矩阵为决策变量的多目标半定规划的最优性条件。
补充资料:SolidWorks属性链接
如图所示,在sw里动态显示零件的体积,面积。


 



首先在前视基准面上建立一个半圆形闭合草图,然后以中心线旋转,如图1所示:
在特征管理器右键单击“注释”,在“显示注释”、“显示特征尺寸”前打勾,如图2所示:




图1



图2


单击菜单“插入”——“注释”,如图3所示:
依次输入,体积、面积、两个注释。(具体自己设置),如图4所示:



图3



图4



鼠标左键单击“体积”,注意到特征管理器中的“属性连接”项,如图5所示:
打开属性连接,单击“文件属性”,分别添加“体积”和“面积”的配置,在“数值/表达式”选项里,在下拉列表中,选择相应的选项——体积、面积。如图6所示:



图5



图6



然后在属性连接管理器中,在下拉列表中找到相应的选项,确定,如图7所示:
同样的方法,添加“面积”的属性连接。下面让我们来看看结果吧,更改特征尺寸,相应的数据随着变化。



图7


这就是属性连接的妙用,处处留心皆学问,大家好好学习。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条