1) job efficiency
制品合格率
2) qualified rate
合格品率
1.
This paper presents the technological analysis for die forming of the oil plug for crankshaft in series 150 diesel engine, and introduces the forming technique that can effectively improve the qualified rate of the oil plug and design outline for the insert block forging die in particular.
对150柴油机曲轴油堵模锻成形进行了工艺性分析,着重介绍了可有效提高油堵合格品率的成形工艺和镶块锻模的设计要点,分析了该油堵成形工艺方法的可行性、实用性和效益性。
3) product qualification ratio
产品合格率
1.
The concepts of raw material utilization ratio,product yield ratio,product qualification ratio as well as the importance for the enterprise are discussed.
本文阐述了肉制品生产中原料利用率、产品出品率和产品合格率的概念及其在企业中的重要性。
4) nonconforming rate
不合格品率
1.
We study the relationship between the PCIs and the nonconforming rate base on the traditional quality management,and establish the relation model between the PCIs and and nonconforming rate whether the process has shift or not.
本文基于传统的质量管理观,研究过程能力指数与产品不合格品率之间的关系,建立了过程有无漂移时的过程能力指数与产品不合格品率之间的关系模型。
2.
Utilizing statistical tolerance technology, the relationship model between process capability indices and nonconforming rate is established.
利用统计公差技术,建立过程能力指数和产品不合格品率的关系模型,在Cp-k确立的平面下对过程质量不合格品率进行监控。
3.
Utilizing statistical tolerance technology,the relationship model is established in process capability indices,the coefficient of process shift and nonconforming rate.
研究利用统计公差技术,构建Cp-k平面内的面向不合格品率的统计公差带模型,建立过程能力指数C_p、过程偏移系数k和产品不合格品率Pd的关系模型。
5) the qualified rate of products
产品合格率
1.
The paper introduce the forecasting and relative degree method of grey systems theory to the quality management area, set up a GM forecasting model for the qualified rate of products and the time intervals of the quality catestrophe.
将灰色系统理论中的预测与关联度理论引入产品质量控制领域，建立了产品合格率产品质量突变区间的ＧＭ预测模型以及产品质量影响因素的关联度诊断分析模型，提出了ＧＭＰｔＣ图，并给出了一个应用案例，为产品质量的预报控制与因素诊断提供了有效分析方法与工
2.
According to the level of the qualified rate of products in the course of the producing texitle products, this artide determines the control limit of control chart,works out the coefficient through the living example.
根据纺织工业的产品合格率水平，确定生产过程控制图的控制界限，并结合实例计算出了对应的数值。
6) product qualified rate
产品合格品率
补充资料：不合格百分率计数检验的序贯抽样方案
不合格百分率计数检验的序贯抽样方案
sequential sampling plans for inspection by attributes for percent nonconforming
加hege比ifen.o Jishu Jianvan dex叩uanC伙泪四叩fa叩’On不合格百分率计数检验的序贯抽样方案(se-quenti吐~plingp】川15 for inspection场attributesforpe二ni nonconfo丽ng)逐个地(或成组地)抽取个体，但事先并不固定它们的个数，根据事先规定的规则，直到可以做出接收或拒收批的决定为止。作为代表性的是IEC 1 123:l卯l标准。 设在n.抽试产品中出现;个不合格，且抽样方案给出:，h两数。判决规则如下:①如;n一h〕r，则接收;②如:n一h
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条