说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 主要(基本)尺寸
1)  principal dimension
主要(基本)尺寸
2)  Main dimensions
主要尺寸
1.
This paper deals with the key points to design aspects of disc type axial-field induction mo tors, such as main dimensions,relationships among main dimensions and power and rotational speed,and optimum value of main dimensions ratio,etc.
本文讨论了盘式轴向磁场感应电动机设计的关键点:主要尺寸的确定、主要尺寸与输出功率和转速间的关系、主要尺寸的最佳值等问题,旨在为盘式电机设计的独特性提出探讨性观点。
3)  Basic dimension
基本尺寸
1.
In this paper,a mathematical model is introduced which,is meant for determining,in the light of the allowable pressure angles of actuating travel,basic dimensions of the disk cam with an oscillating follower.
本文研究了摆动从动件盘形凸轮机构按推程许用压力角确定基本尺寸的数学模型。
2.
This paper studies a kind of distribution for quality characterisics and process diversity extent which are based on asymmetric tolerances and centered on basic dimension.
以基本尺寸为基准,研究非对称偏差下总体质量特性值的分布及过程离散程度,在给出一类非对称分布的基础上,研究基于非对称偏差的过程能力指数,并将其推广到角度质量控制问题。
4)  basic size
基本尺寸
1.
According to the relatimship of measured valve and common differce,we found a scientific and reliable way to define basic size and common differce coordinatio
本文是通过对测绘中所测的实测数据和公差配合标准的科学分析,找出实测值与尺寸公差的内在联系,并根据此关系提出了确定基本尺寸、公差配合的一种较为科学可靠的方法。
5)  Basic dimensions
基本尺寸
1.
A solution method of cam with oscillating follower′s pressure angle and basic dimensions;
摆动从动件盘形凸轮机构基本尺寸的一种求解方法
2.
An analytic method of determining the basic dimensions of the oscillating disk cam mechanism under retangular coordinates is introduced.
介绍了直角坐标下摆动从动件盘形凸轮机构基本尺寸确定的解析法。
3.
An introduction is given of an analytic method determining the basic dimensions of a direct moving driven disk cam mechanism under a retangular coordinates system.
介绍了直角坐标系下直动从动件盘形凸轮机构基本尺寸确定的解析法,通过对凸轮机构中基本尺寸的研究,得出了压力角、基圆半径和偏距的计算公式,为上机运算提供方便。
6)  basic sizes
基本尺寸
1.
The precise formulas and procedures have been developed,for calculating the basic sizes(radius of base circle,arm length of follower,and distance from cam center to follower pivot point) of disk cam according to allowable pressure angle.
研究了最大压力角随径长比(基圆半径和从动件长度的比值)的增大而减小的规律,给出了按许用压力角直接而精确地计算基本尺寸关系的公式及计算步骤,还提出了从动件按基本运动规律运动时的图表计算
补充资料:Pro/Engineer Drawing 工程图尺寸基本操作
2.1 建立尺寸 Creating Dimensions
在图纸模式下,我们可以建立三种类型的尺寸

Reference dimensions
参考尺寸
 利用模型的几何实体建立的参考尺寸,系统会依据视图将尺寸保存在模型以及图纸中。建立的参考尺寸会以REF标记,以示和其它尺寸的区别。
 
Driven dimensions

被驱动尺寸
 所谓被驱动尺寸,是指依赖与模型的边、顶点、参考平面、轴线、点以及修饰特征所建立的尺寸。如参考尺寸一样,这些尺寸受模型尺寸的驱动。

注意如下几点:

驱动尺寸只是在本图纸中显示,系统会将它们保存在模型中。在其它工程图、零件、装配中不显示, 这是参考尺寸和被驱动尺寸的主要区别 
可以指定被驱动尺寸的小数位数,但无论如何也不能驱动模型。它们依赖与模型的改变而改变,不能修改被驱动尺寸的值 
 
Draft dimensions

绘图尺寸
 手工绘制图纸时,建立的尺寸。这种尺寸依赖与图纸的比例以及绘制实体的类型。在PRO/E中,我们建议利用模型来建立工程图,最好不使用手工绘图的方法。这里就不详细介绍了。
 

2.2 建立被驱动或参考尺寸 Create a Driven or Reference Dimension


选择DETAIL > Create,并选择Dimension (被驱动尺寸) or Ref Dim (参考尺寸) 
在菜单LIN ORD中选择尺寸类型
,如果选择 Standard 菜单,则选择需要表尺寸的实体

默认尺寸参考菜单

选择在菜单中边、边和点、两点、或顶点。可以使用下面的菜单方便选择:  On Entity 附着与实体被点中的点,如建立规则的尺寸一样  
Midpoint —选择实体的中点  
Center —选择实体的圆心  
Intersect —两实体的交点
 
Make Line —相对于当前XY轴线建立直线  

注意:要建立弧尺寸,选择圆弧的两断以及圆弧,并在菜单上ARC DIM TYPE 选择 Arc Length .

如果选择了圆弧以及直线,会出现如下菜单;

其中: Center 标注距圆心的距离,Tangent 标注距切点的距离 
关于DIM ORIENT菜单的用法 


2.3 建立尺寸的折引线 

当尺寸附件项目较多时,可以建立尺寸的折引线,将尺寸线引出


菜单:DETAIL>make jog

2.4 建立坐标尺寸 Create a Coordinate Dimension 

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条