1) automatic reverse stitching system
自动倒缝装置
3) automatic name setter
自动缝牌名装置
4) automatic device
自动装置
1.
Generic algorithm research for simulation of automatic device in DTS;
DTS中自动装置仿真通用算法研究
2.
In order to meet the technological requirements of unmanned substation automatic device,a substation APD (reserve source Auto -put-in Device) hardware & software scheme has been proposed.
根据变电站综合自动化对自动装置的要求,提出一种适用于新型变电站主结线形式──三主变四分段结线的备用电源自动投入装置的硬件及软件的设计方案,并论述了其技术特点。
3.
Based on the analysis on the remote control of relay protection and automatic device,a scheme for realizing remote switching-on and switching-off of relay protection and automatic device strap circuit is proposed using high voltage equipment remote control principle.
通过对继电保护及自动装置远方控制问题的分析,提出利用远方控制高压电气设备的原理,将电触发命令转换成位置状态变换、用机械闭锁方式实现自保持功能,实现远方投退继电保护及自动装置压板回路的解决方案。
5) automation device
自动装置
1.
Study of protection and automation device configuration in the island startup mode
孤岛启动模式下的预置保护和自动装置研究
2.
This paper briefly introduces system configurations and functions of 500 kV step-up substation,generator-transformer unit,auxiliary power supply system computer monitoring,computer-controlled relay protection,and automation devices of Huaneng Yuhuan Power Plant 4×1 000 MW project.
文章介绍了浙江华能玉环4×1000MW电厂工程500kV升压站、发变组、厂用电系统计算机监控、微机型继电保护和自动装置的系统配置和功能特点,在电厂二次线设计以及先进设备的使用做了统一的系统规划,并获得了有效的实施。
6) automatic equipment
自动装置
1.
Microcomputer based automatic equipment—developing trend of power system stability control;
微机自动装置是电网稳定控制的发展方向
2.
Through the analysis of emergency trip for 110 kV and lower voltage open network,the coordinated application of auto-enclosure and other automatic equipments in such network was put forward.
通过对110kV及以下开式网络的故障跳闸分析,提出了自动重合闸在110kV及以下开式网络中与其它自动装置的配合具体应用。
3.
Combinated with theoretical analysis,simulation research by PSCAD and pilot study by RTDS,it researches the effects on transformer protection and automatic equipment by harmonics and negative sequence of electric railway.
本文在已有研究基础上,从数字仿真出发,基于某典型电铁牵引供电系统和公用电网,利用电磁暂态分析程序EMTDC/PSCAD建立了主变差动保护和故障录波器的模型,通过理论分析、PSCAD仿真研究与RTDS试验研究相结合的方式,分析电铁谐波和负序对主变保护和自动装置的影响,最终给出相关的结论和建议。
补充资料:包钢无缝钢管收集装置降噪和防冲击研究
包钢无缝钢管厂作为国家大型骨干企业,面临着激烈的市场竞争,因此在保有原有优势的基础上,迫切需要全面提升产品的质量,争取更大的市场份额。包钢无缝钢管厂的设备是五十年代从前苏联引进的,主要生产直径140mm至直径426mm的无缝钢管。在收集过程中,钢管的落差大,产生了噪音和冲击 。冲击使钢管发生了塑性变形,噪音损害了工人的身体健康。作为面向二十一世纪的现代化企业,必须考虑如何在优质高效生产的前提下,创造一个清洁、无污染的生产环境。因此,对于无缝钢管收集装置的深入研究势在必行。 | ||
| ||
使用ANSYS软件进行无缝钢管的变形模拟,其数据真实性得到了现场的认可,且在获得数据的同时并未影响生产。模拟的最终结果为新型无缝钢管收集装置的设计提供了理论依据,目前依据这一模拟结果设计的第一种方案已完成,正在进行第二种方案的设计。 | ||
|
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条