1) self cooled transformer
自冷式变压器
2) self-cooled transformer
自冷式变压器
3) oil-immersed self cooled transformer
油浸自冷式变压器
4) slow cooling
自冷
1.
XRD,XPS,EXAFS,IR TPD,NH 3 TPD and pulse microreactor were used to study the differences in metal dispersion and active constituents on the supports made by mixing γ Al 2O 3 with two different US SSY zeolites,obtained by quick and slow cooling method respectively.
应用ＸＲＤ、ＸＰＳ、ＥＸＡＦＳ、ＩＲ－ＴＰＤ、ＮＨ３－ＴＰＤ和脉冲微反等多种物理和化学方法，研究了以急冷和自冷方法制备的ＵＳ－ＳＳＹ分子筛，在与γ－Ａｌ２Ｏ３制成混和载体时，两者之间的差异对金属组分在其上的分散和活性组分的形成产生的影响以及给加氢处理催化剂性能带来的变化，为制备高效催化剂提供了科学的依
2.
XRD, 29Si, 27AI MAS NMR, the adsorption of nitrogen at low temperature,129Xe NMR, XPS, IR-TPD, NH3-TPD, the high vacuum volumetric analysis and pulse flow microreaction were used to study the difference in structure and property between the US-SSY zeolites obtained by quick and slow cooling after treating SSY zeolite with steam at high temperature.
应用X射线粉末衍射、29Si、27Al魔角旋转核磁共振、低温氮吸附、129Xe核磁共振、X射线光电子能谱、程序升温脱附和脉冲微反等多种物理、化学手段，详细考察了经高温水蒸汽处理后的超稳Y分子筛在急冷和自冷过程中产生的结构和性能差异，结果表明，冷却速率是制备分子筛必要的控制因素。
5) self-cooling
自冷
1.
In this paper,a producing technology of the self-cooling orange beverage has been introduced,the physical cooling principle and system structure are presented,the ingredients of the self-cooling orange beverage technical process and operation key points have been analysed as well.
简要介绍了一种生产自冷式橙汁饮料的物理制冷法的制冷机理及制冷结构设计 ,并举例分析了自冷式橙汁饮料的配方、工艺流程和操作要
2.
This article briefs the basic performance,design,new manufacturing technique and technology of self-cooling enclosed isolated phase bus new products applicable to 1 000 MW generating units,as well as the situations of its passing the inspection,measuring,testing of the relevant national quality inspection center.
介绍了适用于1 000 MW机组用自冷式离相封闭母线新产品的基本性能和设计、制造新技术、新工艺,以及通过国家有关质检中心检测、试验的情况。
6) self cooling
自冷
7) self-cooled crystallization
自冷结晶
1.
Application of self-cooled crystallization process in production of chlorates;
自冷结晶法在氯酸盐生产中的应用
8) Self-cooled leads
自冷引线
9) Self-cooled blanket
自冷包层
10) oil-immersed self-cooling
油浸自冷
补充资料：自动冷镦机、多工位螺栓自动冷镦机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
（一）加工精度 | 参照GB9166-88、JB/T3053-91 | ||||||
1、冲头夹持器模孔中心线对夹持器后支承面的垂直度（mm） 在100长度上 | 0.008 | 0.01 | 0.015 | ＞0.015 | |||
2、凹模座模孔中心线对凹模后座支承面的垂直度（mm） 在100长度上 | 0.008 | 0.01 | 0.015 | ＞0.015 | |||
3、冲头夹持器模孔中心线对滑块行程的平行度（mm） 在100行程上 | 0.016 | 0.02 | 0.02 | ＞0.02 | |||
4、滑块行程对机身上与凹模座贴合的垂直面的垂直度（mm） 在100行程上 | 0.016 | 0.02 | 0.02 | ＞0.02 | |||
5、工件头部对工件杆部中心线的偏移量（mm） | ＜0.20 | 0.20~0.25 | 0.25~0.30 | ＞0.30 | |||
（二）生产率（件/分） | |||||||
20mm | ＞80 | 70 | 65 | ＜65 | |||
30mm | ＞60 | 50 | 45 | ＜45 | |||
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条